I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hello,
I wanted to develop an Hearing Aid Application using nrf52840. I have downloaded nrf connect SDK but cannot find any samples for using HAP profile. Kindly provide...
Hello,
I intend to read the battery level of the nRF9160. I see that I have 2 alternatives to perform this function, using the AT%XVBAT command or reading the battery...
Hello!
I am working on a project that uses nrf52832 microcontroller with softdevice s132 6.1.1. for BLE capabilities. One of requirements is to implement directed advertising...
Hello,
I am building a product prototype based on nrf52810 with s112 7.0.1 with NRFDK16. So the problem is the memory allocation. I setup the FLASH and RAM as per specification...
Hello,
I'm using an NRF5340 with SDK V1.9.1.
I have a code that toggle one gpio pin on a custom board. It is working well when I use P0.22. However, when I change to P0...
Hi all I have a problem with the sim card on our custom board. Earlier I tested my code on nrf9160dk. But on the custom board, the sim card is not recognized. There is no...
We have an nRF5340 application that builds fine for our custom board. However, it is not very straightforward what steps need to be performed to enable FOTA updates. I have...
I am trying to use DTM to evaluate the output filter on our NRF52840 design. I am using the constant output mode and assume that the physical layer setting is not necessary...
Hey guys,
Recently I have been working with the nrf 52840 dongle and my goal is to use the dongle to communicate with a sensor and read values from it. So far I have been...
Hello,
I'm working on development of custom board based of nrf52811, we are using MAXM86161 and ICM-42605 on the custom board but couldn't find any drivers or library...
Hi, The attached picture below captures all the RSSI of our beacons in the field. These devices were set to transmit at maximum transmit power of +4dBm. This max value was...
Hi
I'm trying to get the application timer working on nrf52840 SDK version 17.02
I have followed the below link
devzone.nordicsemi.com/.../application-timer-tutorial...
I am able to print out to Uart but not able to receive from uart.
what do i get wrong?
/* main.c - Application main entry point */
/*
* Copyright (c) 2015-2016...
Hi everyone,
I would like to overwrite my SoftDevice wchich I don't use in my application. I found information about updates without Softdevice.
Its possible to update...
