I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
Hi,
I've started working with the nRF52-DK for developing a new product based on the nRF52832. I'll be using custom services so I took as a starting point the projects provided...
Hi,
I'm using Linux with Visual code extension to compile for both nrf52840DK and nrf52480 dongle and I'm using the programmer in nrfConnect to write to the devices. The...
This case don't happen when i merged net_core and app_core to burn . I used to burn only one core.
What causes this?
Now I have a new question.I use one nrf5340 as CIS...
I am using nRF connect SDK and wanted to examine gpio 'out' register during the debugging session but every time I try to print the register value, I get the following error...
Hi,
I am using the SDK 2.1.1 and I will upgrade to 2.1.4 since errata 160 is fixed there.
Reading the errata document here , the anomaly 168 is fixed in SDK 2.5.1. Unfortunately...
Dear nRF support,
nRF5340 custom board
nRF NCS 2.5.x
Running into this very weird issue:
Program runs fine if I don't attach debugger to it
When I do "attach to...
Hello Nordic Engineer,
I successfully controlled the 52840 DK through Mesh using my phone. However, after exiting the app and reopening it, I can no longer control the...
Hello Team,
I’m working on implementing BLE Mesh on the nRF52832. I extracted the BLE Mesh ZIP file and placed it in the same directory as the nRF SDK. Then, I opened the...
Dear Nordic Support Team,
I am encountering an issue with the nRF52 SDK for Mesh v5.0 and nRF52 SDK v17.0.2 while running the serial example. The system runs for a while...
Hello,
In the header file nrf54l15_types.h, we see the following defines related to the SAADC:
* REFSEL @Bit 12 : Reference control */
#define SAADC_CH_CONFIG_REFSEL_Pos...
Errors on calling "lte_lc_init()"
Does anyone know what the corresponding error codes mean, or what could be done to debug the cause?
Thank you very much.
I am writing an i2s application for the nRF5340 Audio DK with toolchain and nRF Connect SDK v2.9.0.
During development I noticed that nrfx_i2s_start() does not seem to check...
Hi,
I am working on a project where I have two separate physical devices , each based on an nRF52832 :
One device is a BLE Mouse
The other is a BLE Keyboard
My...
Hello, lte_ble_gateway works ok using dk91 or thingy:91 on, v251 - ok v262 - ok but not on, v270 - err v280 - err v290 - err This is straight example code as found in VS....
