I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hello Nordic team!
I had a post where I verified the answer by misclick: https://devzone.nordicsemi.com/f/nordic-q-a/83749/nrf52-dk-as-central-to-discover-services-on...
Hello
I'm using nRF5340 DK with nRF Connect SDK 1.5.0 and SES IDE and I want to change the PHYs and TX power of the peripheral_uart sample ( v1.5.0\nrf\samples\bluetooth...
Hi,
Based on peripheral uart sample code on nRFConnect SDK 1.8, I'm developing a custom BLE application under nRF5340 using VSCODE though nrfConnect extension.
In order...
I tried to program this example developer.nordicsemi.com/.../README.html onto the nRF5340 network core, following the instruction from here devzone.nordicsemi.com/.../ncs...
Hi,
I am new here. I have a very basic question, maybe bordering on Dumb.. but couldn't see the answer in previous questions.
My board will normally be working on AC power...
Hello,
I'd like to remove the "configurations" in Segger Studio and the associated extra directory level; I consider them counter productive.
So how can I get rid of those...
Dear Sir.
A timer is defined for 1 hz,
Every 3 minutes or so we drive the buzzer with different pulses ( see code attached )
We are using the PWM to drive a buzzer...
error repported segger
39 minutes ago
Online lm
47 pts.
Hello, i'm trying to flash a code in my module nrf52805 thx to my Dk nrf52840. i have this error I...
Hi team,
I'm streaming the sensor data through USB (using hterm) every 2.5ms.
i have configures USB as CDC and using virtual COM port.
In each iteration, i transfer...
i have nrf52832 using nrf sdk version_17 and s132.
I have application for logging
i have followed steps:
1). intially device in sleep mode
current: 0.35 micro Amp...
Hi,
I am working at a project that was abandoned by a guy that worked on my position. I have to fix some issues and add some features. I'm using SDK 17.0.2, my IDE is VSCodium...
Dear all,
I am now using two nrf52840DK and nrf connect sdk v1.7.1,and I want to send packet using llpm mode between two devices,one is receiver and the other is sender...
I need a battery-powered programmable device to communicate via Bluetooth to a headset, and communicate with another device via serial (TXD/RXD) interface. Performance requirements...
Hello,
I am writing a single byte value to a cypress module using write with response (BLE_GATT_OP_WRITE_REQ). For some reason the peripheral will receive the value but...
