Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
we are trying to send data (a packet of 54 bytes) at 100Hz but our data is not always transmitting regularly.
Much of the time the TX is perfect but every so often...
Hi,
If i need to call zephyr driver API clock_control_off( ) present in zephyr\include\drivers\clock_control.h on LFCLK. How can I do it,.? As an example, to populate...
We have a RFID sensor reader part number RFM5114 , manufactured by Nordic , the sensors we use to read are RFM2100 Magnus S2 tag. Now we have to read sensors RFM2121 Magnus...
Hi everyone,
Is there a way of being able to view the contents of the advertising packets (advertising and scan response) without using a bluetooth sniffer? Is it possible...
Hello,
I made a code on NCS1.5.0. The main function is to realize audio encoding and decoding. It runs and tests normally on nRF5340 DK. When I migrated this code to NCS1...
Hi, While I'm aware that the specs are not yet finalized, are there already any hardware requirement estimates for running Matter over Thread for a battery powered node? I...
Is it possible to perform an over the air update via Bluetooth Low Energy while the sensor is connected, but the app is running in the background? If this is possible, are...
Hi,
I found that when my custom board spend 201 ms to boot up. Because I can't change my board, I am looking for reducing time to boot up.
Do you have any idea and how...
Can you please tell me why I get an -ENOTSUP error when I set the scan .timeout parameter to anything but 0? Is the suggested workaround to use RTOS functionality to timeout...
Hello All,
I have the following issue - a peripheral and a central using nrf52832 with SDK 15.3 and S132 - on the peripheral I advertise with a whitelist - the central scans...
nRF Connect used to work fine. After the 3.8 update it could no longer see devices. At that point a re-install helped.
Then after the 3.9 update it stopped working again...
Dear support,
I am using nRF52840DK (PCA10056) and nRF5 SDK version: nRF5_SDK_17.0.2_d674dde. I am trying to make all the prints in my application to be displayed properly...
I working with the MDBT42Q-DB with the nRF52805 module. I've started from the ble_app_beacon example in SDK 17.1.0. I was able to compile and run the example in Segger Studio...
Hi.
I used sdk 1.4.0 with nrf9160, I used UART2 to comunicate with another mcu. I run fine and no problem.
Today, I update to SDK 1.6.0, I edited UART2 ( in device tree...
