Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hi,
When I open an example project in the Segger Embedded Studios I can first build without a problem. When I change the target
device under Debugger in the project options...
Hi,
I'm struggling to adjust the BLE_blinky example in the Segger Embedded Studio from the NRF52810 to the NRF52811.
I tried to follow the documentation from here (...
Shalom!
In my central nrf52840 board we connect to a TI BLE sensor that has a customer UUID base service and the TI OAD base service both with 128 UUIDs. I succeeded in...
Hi all,
In my project am sending ecg values over ble to android app. During first connection, the values are received and seems to be no problem, but when i disconnect and...
Hello,
I want to increase the number of peers stored in flash. Right now I have FDS_VIRTUAL_PAGES as 3. If I increase this, would I be able what I need? I just need 10 pages...
Hi guys,
I have a problem opening CMSIS Configuration Wizard, but only in Mesh SDK. Because I am working in this SDK, do you maybe know how can I fix this issue. I checked...
Hi, I was testing NCS v1.5.0 and Azure FOTA application and found a bug in the is_update() function
If the current firmware version is shorter than the new one, it may...
Hello, In our current project we are using NRF9160 with NRF52811 as BT device over HCI. Firmware on NRF52811 is just Bluetooth: HCI UART example with pinmux changed to match...
Hi Nordic team, I'm having a custom board and custom application made for that board. Application is based on the zephyr v2.3.0. I decided to move to the NCS because i want...
Hi guys:
a. I use a uart dfu bootloader(loacation: SDK-location\nRF5_SDK_15.0.0_a53641a\nRF5_SDK_15.0.0_a53641a\examples\dfu\secure_bootloader\pca10056_uart) in 52840 soc...
I'm thinking of replacing the software that was running on "nRF52810 QFN48, S112" with "nRF52810 WLCSP, S112". In WLCSP, the pin assignments of XL1, XL2, nRESET, SWDCLK, SWDIO...
I recently downloaded Keil uVision5 and am trying to run some of the examples that are found in nRF5_SDK_12.3.0 available from on Nordics website on my Nordic51 development...
Hello,
I want to control 2 PWM with different frequencies and hence I am using two separate instances. I want to use only the hardware and not the PWM library. Initializing...
Hi
I am using nRF5_SDK_17.0.2_d674dde with softdevice S140 have sample example as ble_app_cts_c but when i run the code first central disconnected but when i going to pair...
