I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hi Everyone,
I am working on the nrf52832 and i am trying to build the Eddystone beacon application example with segger embedded studio. But when i do, I get the following...
Hello,
I want to modify the default transmit power of the nrf5340 peripheral_uart project.
board:nrf5340 dk
ncs:v1.5.0
example:v1.5.0\nrf\samples\bluetooth\peripheral_uart...
I am trying to figure out how to enable and use the RNG peripheral of the nRF5340.
since the RNG is on the Network side of the nRF5340.
is there anything i need to set...
This is very reproducible...after sending and receiving data in a loop, the modem application becomes unresponsive. Only modification from SDK software is that I am using...
Hello,
I was trying to setup nrf5 board with IoT sdk for tcp connections where the tcp board will act as a server and raspberry pi 3 model B 1.2 as client.
I downloaded...
I am looking for the following products and solutions.
Products :
nRF52-DK
External input :
ADC 1000 Sampling input
1Hz input 3.3 p-p sinewave
Output :
UART...
Hello Sir/Ma'am,
I have used the ble_app_uart (for pca10056) example code to execute the same.
I referred this link to execute my code https://infocenter.nordicsemi.com...
Hi there,
I am using nrf_mtx_trylock.
The explanation of nrf_mtx_trylock is "Try to lock a mutex.".
I would like to lock a mutex forcibly.
Does the function which...
Hi,
I am using the radio test example code where in the interface is through cli. Our custom board has a serial port in UARTE1 instance
how do I configure the cli to...
Hi everyone,
I am trying to develop an application and I need to solve this situation : when the modem is not able to connect to LTE-M network, I still want to be able...
Hi,
I already replied to an old discussion without response so far:
https://devzone.nordicsemi.com/f/nordic-q-a/57449/nrf9160-mipi-rffe-support-for-more-than-one-device...
Hello,
I am using ADuCM350 microcontroller with a build in Bluetooth NRF8001 on board for a school project. I want to program the bluetooth connectivity over SPI0. I will...
Hello Everyone ,
With variety of motion sensors on Thingy:52 , can it be used to detect if a person has fallen ? If 'yes' then how accurate the results will be ?
If...
