Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello. We are planning to change from QFN48 to WLCSP package in our product. However I could't find any guidelines to create the library for Eagle. I was wondering what is...
Goodmorning,
we are trying to update the firmware on a nRF24 development kit board (nRF2727) that was programmed with the PTX sample from your software development kit....
Is there a document comparing the differences between the softdevices for the 51832 ?
I have been looking at the data sheets, but its too much to grock on my own.
Thank...
SDK: 15.2 IDE: Keil SoftDevice: 6.1.1 Board: Custom Hello, I would like to synchronize an SAADC reading during a BLE transmit event. The power source to my board is a CR2032...
Hi,
I am developing an application for Thingy:91 in which I want to send data from the device to MQTT server. I am using 1.1.1 modem firmware and 1.2.0 ncs tag.
The whole...
I'm developing a product using an nRF52840 and an accelerometer.
I have created a Service with characteristic that sends accelerometer data over ble to the phone through...
I add this code in 'static void on_connect(ble_nus_t * p_nus, ble_evt_t const * p_ble_evt) ' on the sever.I got an err_code NRF_ERROR_INVALID_DATA. Softdevice is s132nrf52611...
Hi,
I have a custom board with the nRF52840.
Is it possible to customize the DFU to be able to update the firmware through other interfaces than BLE or USB/UART?
I have...
Hi, I'd like to set up cccd here, but test the error,
In the routine nRF5_SDK_15.3.0_59ac345 nRF5_SDK_15.3.0_59ac345.0_59ac345.s.ble_peripheral?ble_app_uart/pca10040-s132...
Hi.
I have a RAK5010 i use for iot application.
i recently moved from SDK 15.20 to sdk 16. I use the task manager to manage two tasks:
1. task to dump nrf logs
2....
From section 5.2.1.11 I can tell that the peak current with CPU, TX, DC/DC, HFXO running the power consumption would be 8.6n mA. However, I could not find one that included...
Hi, we are developing a home automation product that needs to support ZigBee. However, at the same time I would like the devices to be able to work with a simple non-mesh...
Hi,
I have a question about bit rates of spis slave (Fspis).What is the minimum bit rates of spis slave? nRF52832 need to communicate with a mcu that it only can work on...
I used a translator. Please understand even if the sentence is weird.
Hi, I used nrf52832 QFAA. (RAM : 64kB, Flash : 512kB)
nrf-intel-hex enabled us to check memory...
Hi,
i want to work with nrf9160 for cloud connectivity, can any one help me providing link for working nrf9160 sdk.suggest me how to build samples without any errors using...
