Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I setup one ble mesh network, and it works good for a while. But I encounted a problem that when I power off the mesh node (note: the voltage drops slowly) and then...
Hello,
I am working on nRF51822-QF-AAFQ chip using SDK 12.3.0 in IAR embedded workbench.
My question is, can I impliment DFU in nrf51822 chip?
If possible suggest Starting...
Hello All,
I am trying to add DFU service in the small example with the custom service.
But is not working, facing issues.
I am working on the nrf52810 board with...
Hi all
I am trying to pair nrf52840 (as a central) with ESP32 (as peripheral).
Now I want to get the service uuid so that i can pass to advertising service in ESP32 code...
When restrating the controller, are there any information stored in memory regarding the paired devices or is this up to each implementation to do this manually.
1. If there...
Please tell me about AFH (Adaptive Frequency Hopping).
SDK：15.3.0 例：ble_app_multirole_lesc DeviceA：EYSHJNZWZ（nRF52832）
In AFH (Adaptive Frequency Hopping), the frequency...
Hi,
I am trying to write my own uart init and irq handler routines by accessing the registers directly as per the data sheet. I also referred to https://devzone.nordicsemi...
By some strange reason the thread with my previous question cant accept any replies (and missing the toolbar that appears on the other threads: "Reply Like More"), so will...
Hello,
I accidentally set my board in boot mode and then lost power, then after power on again, the board seems in a total dumb mode: invisible in Device Manager, LED5...
Hello everyone.
I don't know how to start the program when using Soft device.
In the case of example such as example / peripheral / blinky, if it is executed once from...
on the page
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v16.0.0%2Flib_crypto_backend_micro_ecc.html&anchor=lib_crypto_backend_micro_ecc_install
step...
Hi,
I am working on low power mode with DK to apply optimization to our project.
And I verified DK with ble_uart_app can go down to less than 5uA in system on mode which...
I'm still trying more TCP stress testing similar to this inquiry . However, now I'm getting highly repeatable lockups on the node I am doing testing with.
Application code...
I was doing some stress testing of TCP connections and saw an oddity go by that has me scratching my head.
Here's the order of events as best as I can figure from correlating...
