Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm using nrf51822 and SDK 10, S110 Softdevice. Implemented whitelist using device manager and bonded with single device , after bonded my device with phone (using nrfconnect...
I'm using nRF51822 and SDK 10 , Softdevice S110 . I enabled whitelist option in my application its working as expected, but when after device is resetting peer device data...
Hello,
I am working on an application on a nrf52840 using soft-device 140 and SDK 15.3. I have written 90% of the application using the ble_app_uart_c as a template for...
Some context: I am using an nRF51 with SoftDevice S130, which acts takes both central and peripheral roles, and uses UART to communicate to a peer MCU. I am currently facing...
Hello,
I am using Seeger for Flashing code and Debugging. I ported code from “flash_fstorage” example code to “ble_app_blinky”. I have few queries on write data into Flash...
Hello,
I am trying to configure Pin P0.09 as SCL pin for TWI. But I am not getting any results with this pin while I get data when any other GPIO pins are configured as...
SDK: 15.2.0
SoftDevice: s140 6.1.0
Hello,
I seem to keep finding conflicting information on how the NRF52 manages power to its peripheral devices and whether the application...
Dear proffesionals,
I am very beginer to nordic chip.i am using nrf_SDK_15.0.0_a53641a version.i am trying to integrate the writable_ndef_msg file to bluetooth.so how to...
Hello,
I am using custom hardware with an nRF52810 chip, connecting it to P16 connector of the power profiler kit. I use the power profile kit to check power consumption...
Hi guys,
I am a newbie in nRF but with some experiences in embedded systems . I have just been asked to work on a project that connects a nRF52811 to a nRF91.
I initially...
I'm testing a gps sample program below. github.com/.../gps
I have two questions about it.
1. It doesn't acquire NMEA data. it always stops working when it reaches 30 sec...
Hi
I tried to connect my dongle to PC but it is not getting detected , Even the red LED is not blinking., Can someone help me out with this issue
Thanks
Tabassum
I'm using LPCOMP to sense multiple input.
I call the lpcomp_read() function below for each input pin.
If I only call this function for 1 pin only, it worked fine.
For...
Hi,
I'm developing an application requiring multiple connections to several peripherals from a single central. I followed the instructions given here https://devzone.nordicsemi...
Does anybody know a quick and easy way to disable the radio functions in a soft-device application?
I want to measure and optimise the power consumption of all the other...
