Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
HI
UUID scan filters are set and enabled.
I was capturing peripheral device MAC id via ble_evt_handler.
i was expecting filtered devices should be visible but when i...
HI
I am trying filter peripheral devices based on UUID while scanning. I have set, enabled the scan filters but still output is displaying all the peripheral devices irrespective...
Hi I am using nrf52832 board and SDK15.2 I have below requirement:
Nordic board should act as central as soon as it gets booted and scan for particular service if present...
Hi, I have modified the twi_scanner example of the 52840 DK to be compatible with nRFDongle.
I fully erased the dongle with Segger and passed the new hex file with SWD cable...
I found this very useful Throughput Measurement Application for for Threads: http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.thread_zigbee.v2.0.0...
HI, I have a custom service with customs characteristics and I need the maximum speed posible.
I have one service for write without response and another service only with...
Hi,
We implement oob pairing using NFC.
According to my knowledge NFC is used as "private" advertising channel (this is what OOB means) i.e. peripheral address, encryption...
Hi,
I have created a custom Serivice and custom characteristics in the attached application
Please find the attached application which create a custom Characteristic with...
hi nordic,
i had a nrf52 dk where it should only advertise to specific device like my phone with nrf connect app and that nrf52 dk should not advertise to other devices...
Hi,
My name is Bruno and I'm developing an Application which consists on:
Connect to a BLE device (I'm using Nina B112 from u-blox, which contains a NRF52832 SoC) through...
So I have successfully built & deployed the Light Switch Demo - and it works.
But where do we go next?
The documentation seems far too close-in focussed on the microscopic...
Hi,
what is the typical or max wake up time of the nRF52 from the RTC or GPIOTE irq (when configured as sense for low level input)?
In my setup, I see a wakeup time...
Hi,
can I use a pin with A/D converter (or comparator) and at the same time read its logic value using GPIO and configure it to be event source in PPI?
Thanks
I have develop a project on nRF52832 and I want to migrate to nRF52840.
I am able to build pre-devloped project from directory nRF5_SDK_14.2.0_17b948a/example/tasol/ble_app_template...
We have used nRF24L01s in our most recent project but would like to switch to the nRF52832, while still using the Enhanced Shockburst radio protocol.
We are prototyping...
