Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Hi all
nrf52840 Development board,sdk is nRF5_SDK_15.2.0_9412b96 ,PC is windows 10
I want to add the function about bonding and passkey to the example of " ble_app_hrs_freertos...
I have an application where in i need to scan for non connectable advertisements as well as advertise beacons on the device. I am using the Fanstel BT832A module which contains...
Hello,
i would like to interface nrf51822 with an rfid reader mfrc522 using SPI.So, i went through the example of spi_master in SDK 8.1.0.How can we access the value of a...
Hello all,
I am right now working on one project. where i use nrf52832 BLE board. right i am doing i2c communication of temperature sensor(lm6bd) with ble board. but can...
Hello All,
I am using nRF52810 programming in segger embedded studio in windows 7. i am trying to do i2c communication between sensor and nRF52810.i am create custom service...
Hi,
I have a question about direct advertisment - if I direct advertise to one android, then other devices won't show it am I right? How does this direct advertising works...
Hello all,
I am using nRF52810 programming in segger embedded studio in windows 7. I am refer SDK nRF5 v5.2.0. I am trying to do i2c communication between sensor and nRF52810...
I had a couple of questions regarding the SPI slave peripheral on NRF52:
What is the behavior of the peripheral if a transaction completes (NSS goes high) and another...
I used the example code of MQTT pub and sub with nRF52 DK which has nRF52832 in it. I have sent the data from one kit to another with the help of Raspberry pi 3 as a router...
Hello. I need a bit of help with my case. I have nRF52832 dev kit. I have set heap size to zero in Makefile:
And even with that change I am still able to allocate memory...
Hello,
I have some questions about NFC on nRF52832:
1.Could NFC on 52832 works as a card reader , for the mifare 1 card, or named S50 card?
2.In the example "nRF5_SDK_15...
Hi all,
I have read that ANTUSB-m is needed for ANTWARE running in Windows PC. Can I use nRF52840 DK or nF52840 USB dongle in place of ANTUSB-m? If yes, where I can find...
Hi all
I have a custom Board, I have tested it a lot. NRF51822, programed with Mbed..
In general the Software and Board WORKS FINE, but I found some problem in my procedure...
Hello
I am following example on :
examples/dfu/secure_dfu_test_images/ble/nrf52832
when flashing:
sd_s132_bootloader_buttonless_with_setting_page_dfu_secure_ble_debug_without_bonds...
Hello,
I'm trying to use this code https://github.com/kimyd/SHT1X_on_nrf51822 to communicate with an SHT11 sensor via GPIO pins. I have a Saleae hooked up an can see the...
