Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
DevZone displays incorrectly when single word length exceeds the width of the #ContentLeft
div. Instead of wrapping, it expands the div to accommodate, clobbering...
Hi all,
I'm using the nRF iOS Toolbox as a reference to design an app.
Can someone please help me in terms of which swift code file I need to use to read and write data...
Hello,
I've gone through the other posts regarding printf() with floats ( devzone.nordicsemi.com/.../)
and I still can't seem to get float to print. Currently, printf...
This is my coding implementation using mbed online compiler mbed code
and this is serial pc result
and this is the result over BLE using nRF UART app
how this...
ScreenRecord_20171204_133336.mp4
I am working in sdk14.1 nrf52832 ble_app_hids_keyboard_pca10040_s132.
IOS and WIN10 on working ,but android no working .
here is...
Hi all,
We've tried to port IoT SDK features (IPv6 over Bluetooth low energy) to Nordic Thingy 52 .
As base, we use FW for Nordic Thingy 52 from GitHub
We need to send...
The last table on the S132 Specification BLE "data throughput" web page lists the maximum GATT Notification send/receive rates as 16kbps when using an event length of 2.5ms...
I've been following the instructions on how to test buttonless secure DFU without bonds using the Buttonless DFU Template Application page.
I followed the instructions...
I'm trying to port my project from SDK11 to SDK14.
I am having troubles understanding how the drivers supposed to be used.
In the files nrf_peripheralXXX_drv.c there is...
Hi guys,
has anyone had problems with: Cannot connect to J-Link via USB. message?
The device is alive and i can flash and connect to it from CLI.
Thanks
Hi guys,
Many thanks for the help before, I could now running example and change the parameters in the example code for my Taiyo Yuden nRF51 board.
Say, I would like...
Hello,
I don't know how to enable the notifications for a characteristic in the nRF Connect app for iOS. I have the latest version and I tried all the buttons but none...
Hi,
has anyone observed a behavior where the peripheral would be displayed as Accessory on iOS?
I'm seeing this occasionally with my S132 v5.0.0 peripheral, but can't...
In Android, is there any way to distinguish between an explicit disconnect requested by the remote device, and a disconnect due to loss of comms; eg, the remote device going...
Hi.
When I make flash bootloader_secure_ble, it does advertising well.
And I run DFU by making bootloader_secure_ble into .zip file.
However, it does not advertise bootloader_secure_ble...
