Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
I have some initial questions regarding the nPM1300 :) :
- It is possible to download the nPM1300 datasheet as a PDF file instead of viewing it online?
- Regarding VBUS...
When I do a sd_ble_gattc_char_value_by_uuid_read I can only get a maximum of 253 bytes.
And when I read more I get a gatt_status of
BLE_GATT_STATUS_ATTERR_INVALID 0x0100...
when testing NIDD on NRF9151 we are using sock connect -f packet -t raw but it is giving us error
mosh:~$ > sock connect -f packet -t raw sock connect -f packet -t raw Socket...
I want to use RTC in my project. I'm facing build issue (undefined reference to `__device_dts_ord_113') in my project .
STEPS TAKEN: 1. I have enabled the RTC configuration...
Hello everyone.
I am going to do a project recently. We are using dht22 to transmit temperature and humidity, and use temperature values to control LEDs.
This project...
Hello, and thanks for reading. We are having some problems with our device, and hope someone here has the missing piece of wisdom we need. Our device implements HID over GATT...
So in our factory I had setup both an nRF51-DK (PCA10028) and nRF52-DK (PCA10040) to program our external boards we are producing which has a NRF51822-QFAB-R7 populated on...
Hi,
My custom board uses Raytac MDBT53v, which has nRF5340 as its MCU.
My SW is based on the example audio code, and I want to use my external NOR FLAH IC (Macronix MX25R6435F...
Hello,
I am finishing the development of a device based on the nrf52810. When the device is connected to a central, I would like to periodically measure the voltage on VDD...
Hi, I am working on a Bluetooth Mesh project for lighting control using nRF5340. I am currently stuck on how to implement a Bluetooth Mesh gateway for my mesh network. Here...
Hi everyone,
I'm currently working on a project involving an Ember ZigBee end device and a Nordic ZigBee coordinator ( Nordic nRF52840 donngle) . I’ve encountered an issue...
I am not being able to set up the modem in Pakistan. We bought the board in Canada and we've tested it out in Canada without any issues. But the same Soracom sim card is not...
Hi,
I am writing a app.overwrite to remap my pins table. I can use
/delete-node/
The above is no problem. Bu my pio is overlay with gpio1 pin 5. The original dts...
I am using nrf52840 and have two questions regarding flash memory.
1. If the write erase cycles limit is reached for certain page of the flash, only that page is going...
