Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
below is my develop environment .
TOOL : VSC - NRF CONNECT SDK 2.6.99 DEV : NRF7002DK
I am currently looking into the BLE GATT structure in NCS.
Since I need to use...
1. am currently using the nrf9161_dk. and have not modified the modem FW in anyway.
2. I am using the vscode extension provided by nordic to build/run this sample
a, i...
Hello, I am trying to migrate from v2.5.0 to v2.6.0. I had subghz working for the sidewalk samples in v2.5.0 but can't seem to get it working in v2.6.0. I don't see any errors...
Dear Nordic DevZone community,
I am currently grappling with a challenge involving the transmission of data from an NRF52 device to the NRF Toolbox app through BLE.
To...
When I build some example (e.g. samples\bluetooth\direct_test_mode) with NRF Connect SDK Toolchain v2.6.0 and NRF Connect SDK v2.6.0, I get the following errors: warning:...
Development is proceeding with VSCode.
We are developing the source by adding an overlay file to the nRF5340 Audio sample source.
If you copy the entire folder, open the...
I am quite new to the nRF SDK. When setting up an nRF project in VSCode, I can build my project but I cannot flash the target.
My target in this case is an nRF52840-DK....
We have unit testing working with the Zephyr Unity/CMock setup, however the test runner (test_runner_generate) ignores preprocessor directives (#ifdef) and removes them when...
I have an application that must manage different ble connection with different device (and so different UUID services). For the scanning and connection I used the bt_scan_filter_add...
I am using a ble+wifi module which is MS12SF1 which has nrf5340+nrf7002. It is connected with a pcb in which there are 2 inmp621 pdm microphones. I have tried integrating...
I have a dongle attached to my Windows PC and it has the nRF Sniffer firmware flashed onto it. I have also installed the nRF Sniffer extension for Wireshark.
When I start...
Hi
I have been able to work with the 'Lighting' demo BLE mesh application using the nRF Connect SDK with Visual Studio Code. I have even been able to add my custom board...
Dear Madam / Sir,
we started developing a new electronic device which uses Bluetooth 5.0 four years ago and are now ready to certify it. However, during testing we had to...
Hi,
I have designed a custom board, but after production, we are receiving very poor RSSI. I am looking to add an external antenna to the board to see if it can improve...
Hi everyone,
I'm designing a PCB using the nRF5340 MCU and the same matching circuitry (series inductor and parallel capacitor) with parallel ESD protection as provided...
