I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi all, I have a prototype device app I'm going to "deploy" in a remote location with an nrf52840 dongle. Initially ble via special shell commands added to nrf/samples/bluetooth...
Hi all,
I'm new to embedded programing with Nordic I'm using the evaluation of Fanstel EV-BC 805M. I was trying to program the basic program for blinky led, however by the...
Hi,
General information:
nRF52840 SoC
Our own PCB’s with inverted F-antenna
nRF Connect SDK v1.8.0
We are in the middle of approval testing our product. We have...
Dear all,
My application is build on nrf52, nrf connect SDK v2.0.0.
For energy saving purpose, I put the nrf52 into sleep mode, using these code
And wake up via GPIOs...
Hi,
I need to transmit and recieve data over the 2.4GHz radio. I have customized packets to be sent and received over the radio. But I dont want to use ESB or Gazell protocols...
Hello there,
I want to use the nrf52-DK with pc_ble_driver_py. According to the 52832 compatibility matix ( link ) , Revision 3 of the soc needs S132SD v6.1.1 at least....
Hello,
We have developped a product with the nRF52832. Basically, it is a power sensor that uses both BLE (advertising) and ANT+ to send data regularly to a display (third...
Hello, I have a question about the scan request event.
I checked the logs of BLE_GAP_EVT_SCAN_REQ_REPORT. If this event is received, does Softdevice recognize the packet...
What a pity ncs ota not support single bank, but old nrf sdk support.
I know mcuboot not support transfer image over bluetooth, i want to know if there are any other way...
NRF SDK 1.9.1
Modem Firmware 1.3.1
I currently have a production device out in the field that is connecting to a specific cell tower and has the ability to then connect...
hi
I want to use two i2c
But in devicetree add &i2c0 and &i2c1
but it shows undefined reference to `__device_dts_ord_131' and static assertion failed: "/soc/i2c@40004000...
Hi,
I try to advertise nrf52840 dongle on pc to build a connection with nrf5340 uart service. Although I try to modify the advertising program by advertising.py and heart_rate_collector...
Hello there
I need to dynamically initialize and uninitialize the USB HID in my application. Because there is a condition on which I don't want any PC to recognize my device...
Hello there
In the project of the company I work for, we have a device working as a BLE central which connects to a nearby device and checks if that device is registered...
