Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hello,
I have downloaded the app for linux from here: https://www.nordicsemi.com/Products/Development-tools/nRF-Connect-for-desktop/Download?lang=en#infotabs
After downloading...
Hi,
I do have a question about the ble_app_uart for central device. Now it is set to make connection with the periheral based on the UUID. I can't find where in the software...
Hi,
I am writing a program that receives a command from a phone using the BLE UART example. The program can count up or down depending on the command. On every count, I...
Hi,
i'm developing an application that uses scan response.
AFAIK sd_ble_gap_tx_power_set is used to set the advertising tx power (BLE_GAP_TX_POWER_ROLE_ADV).
Is the...
Hello,
I am sunning trying to build the hello world sample as mentioned here:
For this project I am working on ubuntu(VM 22.04.1)
I have followed all the steps as mentioned...
-
Is it better as the ATT MTU size is larger?
I am trying to do nus communication between nrf board 1 and board 2. The data size I want to send is about 30 bytes. Previously...
To make sure that the nRF52840 SoC is not powered when the nRF power switch (SW8) is OFF.
So what happens if I power the nRF52840 SoC when the nRF switch (SW8) is ON ?
Hi ,
When i run samples/keys/hw_unique_key app and select nrf9160dk_nrf9160_ns board . The app can not run into main function instead run into system_halt.
__WEAK...
Please provide the part number(s) of low-cost NORDIC processors that have a quadrature decoder and a PWM.
We are working on an application that is using a Nordic nRF52840...
Hi,
During the validation of our device, we found that the RTC (synthesized from HFCLK) was quite a bit off. Instead of the expected 32.768kHz, we measured 33.047kHz.
...
Hi, I am using urf52832 ( also have 52833 dk).
I am trying to use another pin us uart, which tx is 29 rx is 30 define in project_pinconfig.h.
But I can't see any uart...
Hello, I'm working with BLE Mesh using NRF52840
- Our setup: NRF-Connect-SDK 2.1.0
- Summary of our project.
+ Provisioner node to control lightness for all nodes in...
Hi,
I'm having an issue including USB DFU Trigger library in my prototype application running on nRF52833.
My application is based on the ble_uart example, to which I...
Hi,
My application is written on top of freertos ble example. I need to integrate radio test example as well for certification. I am running into errors when I try to...
