Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I asked this question in a different form but not getting any answers on that thread.
My goal is to publish battery level messages to a certain address and receive it on...
I would like to process and transfer decent quality audio (SBC A2DP) over bluetooth classic in addition to BLE sensor and display data transfer. Not looking for aptX level...
Hello Nordic,
I'm using the official DTM routine to do "SDPPI" certification for Indonesia, but I don't have any test process for Indonesian test engineers to use. Does...
Hi there, we have many nRF52840 devices in the field that currently run firmware based on the nRF5 SDK. We'd like to port our codebase to the nRF Connect SDK for all new products...
Hello,
I'm trying to publish values using a predefined message context.
This works fine when using bt_mesh_onoff_srv_pub or bt_mesh_lvl_srv_pub, but I get a crash...
Hej!
Do you have a reference design for nRF52840 and nRF21540, how to connect the ANT signal (nRF52840) to TRX (nRF21540)?
Is it enough to only use a DC block, C1=1.0pF...
Dear All
I used nRF24L01 antennas with external antenna for data reception and transmission at different speeds (256KBPS, 1MBPS and 2MBPS) for a while everything worked...
Hi
I'm having trouble when trying to connect nRF 52 DK with BLE app on nRF connect for desktop.
I can select device of my nRF52 DK, but cannot not scan any discovered...
HI Nordic, I've looked through all the documentation and tried a bunch of failed experiments...so I thought i'd ask you. On the nrf52840-DK, I'd like to
Connect the DK...
Hi,
I want to program my nRF52833 has tx. The example is provided for pca 10056 and pca 10040. I know that it's possible to change the configuration to use it on pca 10100...
Hello,
I am creating a BLE Rx/Tx connection between two NRF52840-DK's similar to the Nordic UART Service. With the goal to achieve around a 100/100 KB/s connection. Only...
I have a system that consists of a sensor (nRF52840), hub (nRF5340), and gateway (nRF9160). The high level end goal is to be able to publish a MQTT message from the sensor...
Hi,
I'm looking for AES encryption aes_ctr, nrf_crypto example to try on NRF52811 but, I don't see any example for pca10056e.
Does that mean nrf_crypto is not supported...
I tried to deep dive through the macros, api abstractions and other layers but couldn't figure it out. The closest I got is this:
void debug_uart_print(const char * s) ...
