Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
Hi,
We are developing a product (to be produced in small quantities only) that included USB data transfer based on your USB CDC ACM module. We do not have our own USB vendor...
Can an iBasis sim card be activated without being in a device (nRF9160dk or Thingy:91).
I have two sim cards and neither will activate.
Most of the time after entering...
aoa rx hardware: nrf52833DK
aoa tx hardware: my test nrf52833 board
my test nrf52833 board download "direction_finding_connectionless_tx", use " overlay-aoa.conf"
nrf52833DK...
We are currently in the process of looking into the Bluetooth certification as part of a Homekit accessory, and the documentation raised some questions:
the QDID for the...
Hi,
I'm new to ble.
In order to better understand what is going on, on a packet leveI got a packet sniffer.
I found a device that uses a nordic chip, and am trying...
Hi, I am trying to develop an nCS application with serial flash interface, I am using an nRF52833dk & I observed that under the nCS path "v1.8.0\zephyr\drivers\flash" There...
Please guide what changes are to be done for the Light bulb example to be run in 52840 Dongle?
I am using VS Code and built the Build Configuration using the Dongle configuration...
Hello.
I am yoo at korea.
We will connect OLED with QSPI and Driver IC supports SLOWREAD.
- 8bit (Opcode: 0x03) + 24bit (Addr) + 8bit (Read value: Mandatory) + 8bit...
Hello.
I have question for QSPI OPCODE.
According to "nRF52840_PS_V1.5", WREN optional at "the custom Instruction".
- using function: nrf_drv_qspi_cinstr_xfer
...
Hi, I'm trying to use light_lightness example , and button_event_handler didn't work.
Error message is
"multiple definition of "GPIOTE_IRQHandler" "
because I added...
Hi, I'm using nRF52 DK. I'm following tutorial links 1 , 2 and 3 to learn how to add BLE OTA DFU to the example project ble_app_uart.
Step 1
Following the above links...
Dear ,
I am currently testing the UART peripheral on nRF52832 and nRF52840 using nRF Connect SDK.
Basically, I have a sensor that continues sending out data via uart and...
I'm trying to build the pc-ble-driver ( https://github.com/NordicSemiconductor/pc-ble-driver ) to be able to use the nRF52840 as a receiver for a thermometer. See https:/...
I have a custom board with NRF52833 that I'm unable to flash or communicate with using JLinkGDBServer. I was hoping for some help understanding the errors seen in this log...
