I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
We are using a custom board design. I created a custom board configuration when using the v2.5 SDK. In this configuration, we have the UART0 pins configured such that RXD...
Hello,
I am using the nRF54L15-DK development kit. The peripheral-uart example works well to stream data from the kit to a smartphone using the nRF-tools App. However...
Hi
I want to use the timer in counter mode (gpio event shortcut to count task). Do you have any number of current consumption? The plan is to have a 64Hz signal but it could...
Hi, after uploading a Zephyr project (like the "Hello World" example), I couldn't see the device in the serial monitor. i add the below commend in overlay file also but still...
Hello,
I am in the process of following a series of tutorial videos on driving an LED with pwm, but I don't understand how to properly configure my .overlay file and my...
Hi,
I am developing an application for an nRF52840 using nRF Connect SDK v2.9.0. The application currently uses the Zephyr driver for simple PWM functions on several GPIOs...
Hello,
I'm using 'nRF Connect for Desktop v4.2.0' and 'nRF Connect SDK v2.3.0' on windows 11.
I was using vs code well for developing nrf52840 board.
But, I found...
Hi!
How do you recommend to debug crashes?
Especially how do you recommend to debug crashes that happen to our customers that we cannot reproduce?
So far I have been...
Hello!
I'm currently testing writing and erasing data to an external Flash using an nRF5340 and a NOR Flash, the mx25r64.
I'm going to use the SPI_FLASH example.
I bulid...
Hi,
I need to read 16-bit values from a sensor using SPI on the NRF52840. However, since the SPI peripheral only supports an 8-bit word length, what is the best way to handle...
We have nRF5340 LE Audio dks. We intend to check the PDUs transmitted. Does wireshark nrf sniffer support this if yes then how and if not then what is the possible way to...
Hello I want to operate one RGB LED SK6805-EC10-100 for that i need to write data bit by bit in between need to use some delay if any API is there please let me know.
...
Hi,
I noticed that the f_sector_cnt element of the fcb struct is a uint8_t .
How is that supposed to handle large flash sizes? I mean even with a sector of 64KB, the FCB...
Hello Nordic Semiconductor Community,
I am currently working on a project using a custom board based on the E73-2G4M08S1C SoM, which features the nrf52840 chip. For flashing...
