Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Hi,
I already read all similar ticktes but none of them does solve my problem.
i'm using nRF Connect SDK (NCS) with a custom board equipped with nRF52833. To implement...
Hello, I am considering using OpenThread mesh network for an application. I need to know if it is possible to blacklist/remove a device connected to the mesh network from...
Hi Dev team,
I am using the Thingy91 for my development project. I have noticed 1 peculiar issue and wanted to ask for suggestions regarding it.
I had deployed a Thingy91...
Hello there,
I am that newby in the vs code dev environnement. I use the XM122 from acconeer to perform radar measurement. The soft provide by Acconeer compiles and works...
Dear Community;
I am trying to port this code that was made for an nrf52 to an nRF9160. I have a 4.99K pull-up resistor between the data line and VCC.
This is my ds18b20...
Hi, Is it possible to increase the size of the buffer for the UART IRQ RX function such that it receives more than 8 bytes at each interrupt? Currently I am trying to send...
Hello everyone,
I'm reaching out to touch base on the current support status on the latest software (MFW v1.3.1 and NCS v1.7.1) for CoAP over UDP (DTLS) for using as a main...
Hi,
I have a circuit with an I2C peripheral on a separate power switch. There is excessive power consumption (about 50µA extra) due to leakage after TWIM is disabled and...
Hi,
I am using a nRF9160-SICA-B1 and sometimes will see debug output that looks like this in Tera Term:
Glitch example:
Good example:
Basically it appears like...
Hi everybody,
I'd like to perform serial DFU on my nRF52832/nRF52840 based devices, using an external master MCU. Is there any reference C code for the master MCU? In this...
Hello. I am new to Zephyr. I cann't debug Hello_world sample. As i understand it always reboots and does not go to main.
I am trying to use VS Code and nRF Connect SDK ...
NRF Connect shows no device available.
usb interface MCU which embeds a j link is not detected by windows.
LED5 is blinking.
I have an external jlink to try to recover...
I had a project set up and working with my nrf52840 dev kit. It was using the 1.7.0 SDK and was based on the zephyr hello world sample. Today when I open VS Code, the project...
