Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello,
In a previous post I asked about scanning and connecting based on specific advertised data. After some testing I realized that my two nrf dks only connect sometimes...
Hello; We want to use the GPS peripheral of nRF9160. Qorvo QM14501SR LNA is used in your evaluation board. QM14501SR is expensive for our project. Can we use LNA without band...
Hi,
i am working on nrf52832 . i am facing advertising issue with custom board. controller advertise only when i touch 32.786kHz crystals or two capacitors with my finger...
Hi,
I use example projects Thread: CoAP Client and Thread: CoAP Server . I can send and receive data over CoAP. My purpose is to use CoAP, CoAPS and UDP tohether. If client...
nrf_ringbuf has a bug which happens when mixing nrf_ringbuf_cpy_put() with nrf_ringbuf_alloc() and nrf_ringbuf_put(). After copying data with nrf_ringbuf_cpy_put() a later...
Hello,
at the moment we are trying to realize a low power delay with the usage of the APP_TIMER.
We need a low power delay over 10 seconds.
This is our attempt:
...
Hello,
we are developing an application with a nRF52832 on a custom board. The application works fine. The application on the nRF52832 consumes 2.2mA @ 2.5V.
The other...
Hello,
Our Project
at the moment we are developing an application with a BMD-350, which contains a nRF52832 chip.
The BMD-350 is on a custom PCB with another microcontroller...
Hi,
I am trying to prgram the nRF52840 DK board (revision 2.0.1) within a virual machine (VirtualBox running Linux Mint). I have installed the SDK and the nrf command line...
I'm not even exactly sure how to describe this problem, so please bear with me. I have a setup with two nRF52840s, one of them (call it B) functions as a peripheral server...
I have two devices, both nRF52840, one as Client, one as Server. There are a few services defined with a few characteristics in each. Two of the services have values like...
I have now had two units exhibit nearly the exact same behavior, and it seems odd to me for them to be so similar. I'm wondering if anyone else has seen similar. I have a...
Hey all,
I have a USB CDC ACM application that works great when it starts, but I'm not able to get it running without the debugger. This is SDK 17.0.2, there is a SoftDevice...
