Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hello I am in the process of developing a central BLE and I would like to be able to transmit 240 byte frames with a device. The problem I have during my tests is that I see...
Hi,
I get " Could not fetch memory size of target devkit: Error: Error occured when get library info. Errorcode: CouldNotOpenDevice (0x4) Lowlevel error: LOW_VOLTAGE (fffffff4...
I want to use 9 axis motion sensor and I am planning to use INVENSENSE ICM-20948 for this. I know that all the sensors can interface with I2C protocol but the problem is I...
Hello,
DK: nrf52840
SDK: 15.0.0
i want to advertise accelerometer data with BLE/Beacon
so i tried to update the adv. packet for every 10 sec but its not advertising...
BLE DFU Mcu Mgr Error: NOT_SUPPORTED (8)
I am testing the DFU via BLE and get the message "NOT_SUPPORTED (8)" Does anyone have an idea what is not supported?
I logged the following error when I connect my PCA10040 nRF52 development board. The error is: Could not fetch memory size of target devkit: Error: Error occured when get...
Hi there,
First of all; I have experience in Keil but I am new to SEGGER and Zephyr.
Rebuilding our project in Segger using the new nRF Connect SDK I am stuck at adding...
Hi,
I'm running example mqttsn_sleepy_subscriber from nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 on a nRF52840-DK with Paho MQTT-SN gateway on a Raspberry Pi 3 running...
I am using S132 v7.0.1 and while basic Softdevice functionality appears to work fine, I am getting an invalid address error when calling sd_ble_enable(). The pointer that...
I having issues when merging softdevice and application hex files together. If I use nrfConnect and I add the two hex files not merged ( ble_app.hex and s132_nrf52_7.2.0_softdevice...
Hi. I was wandering if there is a difference if I put the TASKS_CALIBRATEOFFSET before TASKS_START , and vise versa. However, I saw in this link: infocenter.nordicsemi.com...
Hi,
According to the documentation the maximum admissible current for the DUT in ampere mode is 1A. What happens if the current goes higher than this ? I suppose that it...
Hi,
I would like to store 180 000 bytes on the flash with fstorage. By using the example after some trouble it works. When I try to apply this example on my own program...
I've seen several questions on this forum on issues with setting up the NRF LOG, however, I am still having many issues and I can't seem to get UART logging working.
I am...
Trying to test the 1ms sample on the NRF5340DK. Loaded and ran the app without problem.. it starts with 9XXXXus. Runs with couple of drops. But when 1ms interval is started...
