We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello,
I watched some of your webinars from the embedded world with the nrf connect SDK and wanted to give it a try. The basic examples (blinking an LED, …) worked fine...
Hello,
I'm trying to read data from the Thingy:91 via the REST-API. I can list the devices and query the state of the device, but I'm not sure how to progress.
So far...
Hello,
I'm working on getting PSM mode in LTE-M working so I can go to very low current operation between transmits to the cloud. I have things working pretty well, but...
We are using over own server that host multiple apis for different functionalities.
I am able to make http post requests to all of them individually and everything works...
Hi
I am about to make an application where a device is sending a sync pulse (60Hz) out to a number of Host's.
when I test with a device and a host, I get approx. 1.22ms...
I am having trouble finding a commercially available BLE 5 dongle that I can be confident will support Linux BlueZ as well as the LE 2M PHY. I would like to know if I can...
Hello,
I have an evaluation board with a nRF52832 chip on it. I added some code to ble_app_uart example and flashed it on the evaluation board.
Here is my problem: I added...
Hi,
I'm trying to use BLE to send data to a computer from the NRF52840 DK. So far I'm trying to get nrf_sdh_enable_request() to compile without errors, but I keep getting...
Hello,
I have both an installation of NCS v1.5.0 from Toolchain Manager (TM) and from the Getting Started Assistant (GSA) on Macbook running macOS High Sierra. The TM SDK...
Hi
I am using nRF9160DK board and need transmit gps data to web site, I am trying with udp but have problems with that, I would like to know what protocol use asset_tracker...
Hello,
at the moment I am trying to implement a counter that increments every 1ms. I wrote the following code for this:
Regarding to the documentation ( https://infocenter...
Hi there,
I am running a custom board based on the nRF5340-DK. It's a minimal board, notably with both oscillators
It seems to behave itself with low-rate BLE use-cases...
Hi.
I'm having trouble flashing my Thingy:91 with the nRF9160DK as a debug probe.
The DK is set to 1.8V, I have a 10pin JTAG cable connected to the debug out of the DK...
What is the UICR setting in nrf51822,S110? Currently, when I develop with nrf51822,S110, the UICR area is 0xFF. I want to set the UICR as follows, is there any way to set...
