Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hi, I am looking where can I get the ACK from the light bulb, in Zigbee light control example. I am using the latest sdk nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8.
what...
Hi,
The documentation for the simple_on_off model in the nRF5 SDK for MESH v4.1.0 states that the light_switch example uses the simple_on_off model.
The documentation...
I think spi slave pins should set as input but I want to control CSN pin as output in spi slave mode on nrf52840. Is it possible it?
I know that CSN pin is controlled by...
Thingy91 is useless without working samples and SDK
Out of the box it cannot associate with any NB-IoT cells here in Bulgaria. I tied using the provided SIM card from iBasis...
Hi I am having some trouble changing BLE connection parameters (mainly due to the connection handle). Is there any working example that I can refer to, which explains how...
Hi Nordic folks,
Our project is using nrf52840-DK boards as the development beds. We're developing a security application by leveraging the internal CryptoCell CC310 inside...
Hi everyone,
I successfully tested the example of the MQTT publisher in the IOT sdk on a NRF52840 and a raspberry pi 3+. The messages end up in my mosquitto install and...
Hi,
We have seen random ARM faults.
After some time we have seen that the lr register often pointed to entropy_cc310_rng_get_entropy.
This is our setup:
- Environment...
I recently purchased nRF52840 DK. While scanning through the website, I came across a suggestion to start with Blinky example. I opened the project in Segger Embedded studio...
Hi,
Observed that Openthread CLI project in NCS v1.3.0 is not compiling as it is using Segger Studio but building with command line. Please fix this.
Thanks
Sridh...
Hi Nordic experts,
I am trying to use Segger IDE to build the mcuboot boot-loader for NRF52x development kit. I am using NRF connect SDK 1.3.0 While I can build it successfully...
Hi
I am facing two issues in the below code. I use segger embedded studio.
1.The value I am setting as fs_initialized = true in line number 90 (inside FRESULT fs_init...
Hello,
I'm working with nRF5 SDK v16.0.0.
The documentation on Hardfault handler implementation clearly suggests to define DEBUG_NRF in order to get an automatic breakpoint...
I have the Thingy91 module, everything is working when I (turn off modem then) set AT%XSYSTEMMODE=1,0,0,0 (and turn on modem again), but if I power cycle the device the original...
