Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi,
I am trying to integrate ble based bootloader into my existing system running on nrf52840. I am using SDK 16 v7.0.1 with sd140. To test the process, I have added the...
Hi, I am working on the ble_app_template project. 1-How can I enable simple pairing without NFC? 2-Also how can I set pairing code? 3-Is the write way to secure characteristics...
Hi, I am developing the project where to read the sensor data and send the values to the mobile application as User Interface. I have built the Board with nRF52832 and using...
The size of the FIFO is sufficient. The value is extracted from the FIFO after being received by the UART. Repeat UART reception.
APP_UART_FIFO_ERROR occurs in the above...
Hi everyone,
I'm using SDK 15.0.0 S132v6.0 and looking for a way to get an event when the advertising times out. I discovered the softdevice_ble_evt_handler_set() in this...
Hi,
I am developing a device based on the PCA10059 board, SDK v15.3.0, and softdevice v6.1.1, and I want to imply that I am using the FDS module with 20 pages in my firmware...
Even after I get a license for the Nordic stuff, SES won't show an installed activation:
The license "installs" fine though:
And I do have the "Nordic" version...
Hello,
When I try and use nRF connect Programmer to update the modem firmware via USB it fails each time in the second step (Modem Firmware Update) with the error message...
Hello Nordic,
I'm working with NRF52840 (with SDK 16 and softdevice s140 7.0.1) in my project, which acts as a central, and an IOS phone as a peripheral. I have a read/write...
I have an nrf52833 wired up to 25 switches and detect changes via the pin SENSE configuration triggering the GPIOTE PORT interrupt. My interrupt handler: 1. reads the pin...
Due to whitelist limitation of 8 peers, I am doing manual filtering of bonded devices. I am trying to use pm_address_resolve function to figure out whether I have previously...
I am using nrf52840 DK and communicate with Raspberry Pi 3 through UART port. The Raspberry Pi is used as a gateway. The baud rate is set at 115200 default on both nrf52840...
Hi, I am trying to integrate ADC in my project( ble_app_template ) but getting garbage data. I have nothing connected with pin P0.4(NRF_SAADC_INPUT_AIN1) . (Means not applied...
I am budding Embedded Engineer, currently, I would like to learn how to program nrf52dk. While I am exploring info center, Peripheral examples I have noticed that most of...
Hi,
I have successfully created the bsd_os port for BSD lib. Everything runs without crashing. However bsd_init always returns 3, no mater what. Which in turn causes the...
