Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
SDK: 17.0.0
Softdevice : S140
Example: ble_app_blink
I modify this example to long range adverting mode,and have some questions as follow:
(1) the device can not connect...
Hi there,
I'm working on a Zigbee project and I'm using the nRF5 SDK for Thread and Zigbee v4.1.0. For benchmarking purposes I need to read the number of hops a Zigbee-packet...
Hello,
I am doing on a project which send data from sensors node to thingspeak, and I am now struggling about implement mqtt to publish data to thingspeak.
best regards...
now i use segger development tool ,but can not breakpoint. but log aseggerlso cannot output information.
V4.2.
my colleague's will do
thanks
best regards!
II'm having issues communicating to the MLX90614, datasheet attached. It seems that I have everything set correctly and the TWI Scanner returns addresses and data. My output...
I am looking for a zephyr based sample code to use an external QSPI flash (MACRONIX MX25R6435FZAIL0). The code is run an nRF52840 based custom board
Your help is appreciated...
Hi,
the nrfx driver for the internal temperature sensor has been introduced with SDK 16,0.0, Since I started developing with SDK 15.02, I have used so far the old HAL driver...
我对NRF6707 Power Profiler套件第一次使用有一些疑问，我想问你 ：
用Amr仿真器JILNK连接NF6707 报错 log日志如下:
2019-11-22T05:21:57.594Z INFO Application data folder: C:\Users\dell\AppData\Roaming\nrfconnect...
Hi
I'm testing heart_rate_collector in pc-ble-driver. in CONSOLE application, it work well.
but in Win32 Application, it doesn't work when run sd_rpc_open().
error code...
Hi Nordic
I want to integrate a push button with 52833 p1.8, base on mesh-sdk light-switch example, (i.e., I may need to modify simple_hal.c)
But after my hours implementation...
Hi,
in some earlier discussions https://devzone.nordicsemi.com/f/nordic-q-a/58652/additional-questions-to-nrf52832-errata-220-clearification and https://devzone.nordicsemi...
Hello,
iam using nrf52832 wiht nrf5 sdk17. we built our application code on ble_app_hids_mouse, now i would like to know how to carefully isolate this file from entire sdk...
