nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Hi,
How i can make the low power node to wake up until get acknowledgement . Please tell me how many ways we can try...In my project i used initiate_friendship() function...
It appears to me that the zb_zdo_ep_resp_t struct is missing a variable value attribute since the actual list of end points is missing. Should it not be similar to zb_zdo_match_desc_param_t...
Hallo All :-)
As an enthousiast hobbyist I've developed a custom board around an nRF52832-CIAA. When I started testing with a BLE secure bootloader from the SDK16 examples...
Hi,
I am currently working on " asset_tracke r" application. Actually, I need to read 128-bit UUID values of the BLE ibeacons present nearby the board (PCA10090) to be captured...
Hi, everyone!
We try to use THINGY:52 board for debug our MEMS lib from external sensor. But before use external sensor (i2c bus) i can't burn standard firmware that compiled...
Hi all,
I'm working with the reception of 802.15.4 packets on nRF52840 for which I have configure the radio as follows:
In the application loop we have:
...
Hi,
I am using nRF52 SDK v16 and I am wondering where one can find relevant information regarding peripheral event handlers.
Here are a few puzzles I have for now:
...
the central(phone) connected my board,when i call sd_ble_gap_disconnect ,sometimes,not every,return err_code =0x00000008,and not firing BLE_GAP_EVT_DISCONNECTED,also not advertising...
Hello All:
I am working on the time service of NRF52. As I know, there are two standard profiles refer to the time service, one is CTS(Current Time Service) and the other...
Hi All,
I am doing a BLE Mesh development project with nRF52840. SDK version: nRF5 SDK v15.3.0 & nRF5 SDK for Mesh v3.2.0
Case 1:
- IDE: Keil
- Example tested: nRF5...
Hi,
Im working on a configuration where role switching is neccessary.
The following is expected:
- all nodes will be advertising when "idle"
- nodes only need to...
Hi,
When the ble_stack_init(); is called the eeprom flash read/write/erash gets hanged.
But when commented ble_stack_init(); the eeprom flash read/write/erash works...
I recently got a Thingy:91 and activated it. Now I am installing the tools to work with it in my system (Linux) following the nrf Connect v3.3.0 Getting Started Assistant...
