Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
can we change duty of one channel of an instance of modules\nrfx\drivers\src\nrfx_pwm.c without affecting or introducing any glitches to other channels of that instance...
I am trying to get an SD card working with the NRF52832 chip, starting with the sd card example (SDK 14.2) using the fatfs module.
The SD card I am using is a Kingston 8GB...
Hi I'm using nrf52DK board with SDK 14.02. I wanted to use PWM Library with softdeivce but I'm getting this <error> app: ERROR 3735928559 [Unknown error code] at E:\nRF5_SDK_14...
I have a Raytac module which contains a nrf52810 AT module in it hooked up to a micro via Uart, so i can send and receive AT commands and data. I'm trying to connect to my...
Hi, I have developed one custom application and enabled DFU features in it.
With the help of nRF Toolbox mobile application, I am changing the application code.
Now I...
I just installed the nRF9160 DK but it showed yellow exclamation marks at the CDC and BULK interfaces. I'm using Windows 7. I couldn't find where these drivers are.
Anyone...
How do I use PWM on a GPIO on port 1 on SDK 15.2? The PWM library examples only sends in the pin number and seems to assume port 0. This answer seemed a bit complex and I...
Dear all,
I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 and S132 SoftDevice v6.1.0 to do some tests . But now I encounter the disconnect reason 0x22...
Hi guys, help me please.....
I want to build a device act like both keyboards and mouse. I've made some progress that the device can connect to my PC(win10) successfully...
Hi all
I developed my custom NRF52840 pcb followed by nordic design..i have done program flashing.Blinky LED also working.But Beacon advertising is not working.while flashing...
Dear Sir
I was working with nrf52832.
.SDK version ------------- 'nRF5_SDK_15.0.0_a53641a'
Soft device - s132_nrf52_6.0.0_softdevice.hex
I was handling a scenario...
I measured the consumption of nrf52832, in deep sleep mode, the consumption is 32uA, the question is: there is a pulse about 5mA every 39ms, is that all right? what's the...
