Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Is there any way to get some "modern" content assist features in µVision that work with the Nordic SDK? If they're there, I haven't had any luck finding them. After having...
I'm trying to decide whether to use FreeRTOS or simply build on the Scheduler. What are the risks and benefits of using freeRTOS or another RTOS on a wearable sensor device...
Is it possible to connected two separated antennas (single ended), one for RX and another for TX communications to the receiver and transmitter of the NRF51 or NRF52?
Thanks...
In other words, is it safe to assume that in various BLE events, conn_handle is either invalid (0xFFFF) or between 0 and (CENTRAL_LINK_COUNT + PERIPHERAL_LINK_COUNT - 1) ...
I'm digging my way through the examples, SDK code, etc, and I'm curious if it's possible to light an LED if the nRF52832 is reaching an error status. This is mainly so I can...
Hello,
I am seeing a strange problem with the nRF52 RADIO peripheral: sometimes a packet will be received that is corrupted, but the CRCSTATUS register indicates the CRC...
My company is developing an embedded product based on NRF52 and until now we are
using Master Control Panel (MCP) to test BLE communication. MCP is a great tool
but we need...
Hi,
when trying to connect to a 51822 target, using for example OOCD
I keep getting
....
Open On-Chip Debugger 0.10.0-rc1-dev-00001-gc404ff5-dirty (2016-12-29-19:45...
I use PPK wit ha stardard setup with all switches set to DK. Everything works fine, excepted that I have a little offset and the IDLE state is negative... which make the AVG...
I have designed a few PCBs using the NRF52 chip with a standard QFN48 pattern. On the first design, we had 8 PCB's made of which, only 2 worked correctly. The others all exhibited...
Hello,
I received BLE_ERROR_GATTS_SYS_ATTR_MISSING event during connection procedure. Tried to look inside and found
/**@brief Event structure for @ref BLE_GATTS_EVT_SYS_ATTR_MISSING...
In code:
case PM_EVT_BONDED_PEER_CONNECTED:
NRF_LOG_DEBUG("Connected to previously bonded device\r\n");
err_code = pm_peer_rank_highest(p_evt->peer_id);
i get...
Hello there,
We're getting an assert in the above code in Soft Device s110 sdk 8.0.3. Can you give us some info as to what that is and how we can address it? To give you...
(EN)
I'm afraid I might no be competent enough, so I look forward to your kind help.
I'm quite new to using nRF52832 WLCSP package(raytac MDBT42 blank module) on a custom...
