I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi, I was reading through the errata for SoftReset and see a note: [161] RESET: Network core is not fully reset after Force-OFF
Can you please clarify how to reset both...
I'm trying to use Adafruit LSM6DSOX (I think it's a misprint and it's actually LSM6DSO), regardless. I can get it to work using I2C but I need it over SPI.
I have been racking...
Hi,
I am working on a board combination of nrf52840 and HL7800 modem. So, I just migrated from 3.6.0 zephyr to 3.7.0 and ncs 2.7-branch.
modem driver: https://github.com...
Hello, I need to scan the advertising data of my peripheral wich advertise with extended advertsing and LE coded PHY.
I use zephyr 3.7, and I work if I use the BLE controller...
Using Modem FW 1.3.6. Using NCS 2.6.0.
We're experiencing an issue in a test setup where we are getting this error reported (528) when trying to clear/set root certificates...
Hello nRF Team,
I am developing a ble terminal app based on the Bluetooth: Peripheral UART sample (nRF Connect SDKv2.7.0) on nRF52840DK. I was testing the app BLE pairing...
When following the unit test example, and even with an alternate minimal implementation, I get the following error:
PS {nRF Connect terminal} > west build -b nrf52840dk...
To people who might be interested in this ticket
I'm trying to make a WiFi connection using the nRF7002 chip. It is a custom board based on STM32 chip. My question is, is...
example:ble_app_uart+ esb_timeslot SDK17.1 Hi Recently our product (PRX) received poor esb communication. I caught through sniffer that when PTX sends a message, our device...
Hi, I have gone through Lesson 4 in Wifi fundamentals. But exercise 1 fails to compile. I have also tested to compile the solution-project, but with the same result. There...
When I look at eh graphic .overlay, I see that the UART0 is there, but no node is assigned. Is there a Node for a two wire UART Driver with no flow control? Peripheral only...
Hello,
I bought a new USB keyboard and since i can't detect anymore Nordic Devboard as nRF5380. No device detected on Visual Studio Code, and on nRFProgrammer neither. ...
Hi,
I working on a project where i measure the distance between nrf52840 dongle and nrf52840 dk using multi carrier phase difference method.
Now, i want to display the...
Hello.
I'm currently trying to send AT Command using an external MCU or USB to UART to check LTE on the NRF9160. The board I use is the nRF9160DK. I changed the pins of...
HI,
I have two solar panes for my project 3W 5V and 2 W 9V. I would to measure current of the panels with the Power Profiler II.
I think this should work (my calc is 3W...
