Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
If the image we falshed using mcumgr is 90% of the allowed image size mcumgr flashes the unit without a problem, If the image is 98% the proccess seems stuck.
...
I am receiving bytes from a GPS module and passing them to BLE UART example app configured to use UARTE1 and asynchronous API.
After few minutes of running it starts leaking...
Hello everyone, I have two nrf5340 kits. I run "Bluetooth Direction Connectionless" applications with these kits. I also have a CoreHW brand AoA antenna. My question to you...
Hi, I have a custom board running with the nrf9160. It also has the npm1300. I have it set up so that it is configuring the pmic and then turns off the cell and goes to sleep...
Hi
Can we use nrd52840dk as bluetooth(for data transmission to user created mobile app) and to calculate distance using multi carrier phase difference method between itself...
We are having an issue with
This happens to us because we are using the NRF carrier library, and in the carrier library, when you are trying to power off the modem,...
Hi, I'm coding a nrf55832, my code uses TWI, UART, SPI, app_timer, nrf_drv_timer. The code was going welle until i add the saadc. When i call the nrf_drv_saadc_init function...
Dear Nordic Engineers
I used gd25lq32e to replace mx25r6435 and it is a 32Mbit Flash, when I add it to the Devicetree of Lwmwm(NCS 2.6.1), the build will report the following...
I'm currently working on a POC for the nRF9160 with an external host processor. I have the Serial LTE Modem example running on the nRF9160 and have the serial comms between...
Hi,
I have a simple question ... I think.
I have been limiting my USBD reads/writes to 64 bytes as NRFX_USBD_EPSIZE and NRF_DRV_USBD_EPSIZE are set to 64 bytes. I have...
Hi all,
I am using the nRF5340 DK. I am trying to run the ncs/nrf/samples/openthread/cli sample with no changes. I have tested this in both ncs v2.7.0 and v2.6.2. I am able...
I'm adapting the sample code for TF-M secure peripheral sample (NCS v2.5.0, nrf/samples/tfm/tfm_secure_peripheral ) to also add a UART peripheral. But this sample uses the...
If there are any compile errors in a LOG_xxx call, the compiler prints so many error messages that it becomes impossible to tell which is the actual error. E.g. below is the...
