Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi there,
The blinky sample worked fine on the nRF52840-dongle when programmed via the stock bootloader, but I need to flash it via J-Link to reproduce an issue.
When...
Hello,We have tested the mesh v2.1.1 in the nRF52830 chip, I want to add a PA/LNA with the nRF52832 so that range anxiety can be reduced.we successfully configured and tested...
Hello !
So i have this issue. I use nrf52840 Dongle, from some article long time ago i saw that i cant connect dongle to VS Code because it does not support bootloader,...
Hi,
As well know, nRF52832 TWI interface can support clock stretch function.
Can I disable "clock stretch function" function?
How to do this job?
Thank you
I am working on nrf52840 and using v2.7.0 SDK. in led_state_def.h (i modified it a little)
static const struct led_effect led_effect [] = {
[ LED_EFFECT_ID_OFF ] = LED_EFFECT_LED_OFF...
I am using SDK16 and attempting to load images for loading.I have questions and would welcome pointers
1. I need to use the application to load a new image into memory ready...
Hi,
I'm working through building my own Matter device. Building on MacOS, VSCode on 2.7.0. I'm using an nrf52840DK for now.
I have two endpoints that contain a temperature...
https://community.element14.com/products/roadtest/rv/roadtest_reviews/1646/draft_for_nrf5340
Above link is a user experience with one of you development kits, which is typical...
Hi, we are working on an application that makes heavy use of work queues. We'd like some way to monitor work queue events to optimize timings/priorities etc. I was looking...
I am trying to make a remote control with NRF24 and Atmega328p. The full name of the NRF24 I am using is E01-ML01SP2. I fixed everything but it draws too much current. I have...
We are looking for BLE Mesh Sniffer,
it has come to our notice nordic provides nrf sniffer. can we sniff BLE Mesh Packet?
Will this mentioned link sniffer be of any use...
Hi all,
I have developed a project for nrf52811 on nrf52840DK.
My question is how I flash this project into nrf52811 using nrf52840DK.
I am using nrf5 sdk 17.1.0...
Case 1: Constantly power on reset during the network attachment process. The customer produced 2000 pcs , 300 pcs defective rate. We measured the voltage of VDD1 and VDD2...
I modified the BLE fundamentals lesson 5 exercise 2 example ( github repo ) for my purposes. This uses a generated passkey for pairing with accept lists.
I removed the...
I've had success getting the Sigurd Hellesvik Serial Recovery sample to work on an nRF52840 DK with mcumgr cli commands. I'm able to flash the Fanstel 840 with the same bootloader...
