Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello:
I am Enrique Martinez. Currently I work with nRF52840 in nRFConnect SDK for VS Code. I have problems with documentation about Multi-Image builds ( https://developer...
I am using the Direct Test Mode sample as a starting point (samples\bluetooth\direct_test_mode). I am using NRF Connect SDK Toolchain v2.5.0 and NRF Connect SDK v2.5.0. I...
As far as I know, ppk2 is an eye-catching and open source power evaluation tool. I got the source code of the power profiler from github, and obtained the hardware design...
Hello,
With the CMakeLists file, is it possible to make an error during compilation if the SDK version is not the correct one?
Example: I am developing an application...
I'm trying to modify this bit-banging ws2812 gpio Zephy driver to run on an nrf9160 board. The problem is I can't mange to get consistent pulse timing using assembly instructions...
Hello
I have a problem setting up communication between a nRF9161 and a nRF52840.
I have a custom board with a nRf9161 and a nRF52840. These two are connected with 5 lines...
Hello, I'm using the nrf5340 and nrf Connect SDK 2.6.1. Currently the MCUBoot is immutable and the cpuapp image is encrypted (it contains IP and secrets). The MCUBoot is kept...
Hello,
I 'm updating from Zephyr 3 .2.99 to Zephyr 3 . 4.99 .
I attempted to add a main() function to my application . (Heretofore I have not been using a main() function...
hello I am designing a custom PCB using an nRF5340 and i have one nRF5340 audio dk with me and both are configured as a gateway and headset . i am facing an issue in pairing...
To do this by reusing the sample of nRF5340 Audio I am thinking of using it by editing the overlay file.
nRF5340 Audio has A/D linked to P0.24, Use P0.24 separately from...
When I tried to use the sd_ble_gatts_value_get() function and found no error but no corresponding value returned, I was sure I had the right value in my feature because it...
Hi,
I try to create a one-button minimal "smart watch" based on a small nRF52840 module (register button press) and a second nRF52840 'central station' (receiving and converting...
hi there i hope you are doing fine and best of your health. actually i am developing the custom app to communicate with nrf 52840 soc device through bluetooth, which is working...
I am using PCA10056 3.0.2 dk for my application
when search for schematics of this version board I am getting 1.0.x https://docs.nordicsemi.com/bundle/ug_nrf52840_dk/page...
Hello everyone,
I'm looking for some advice on a slightly offbeat topic related to the Nordic SDK.
I'd like to modify the Makefile of one of the SDK examples so that it...
