Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello, I am new to BLE and I need help with Battery Service notifications. I am using nrf52840dk, nrf sdk 17.1.0 and I am using ble_app_proximity example which already uses...
Hi all, I have used the nRF mesh app to provision three nodes into a mesh and verified the functionality using the mesh app. I used the export function to dump the mesh configuration...
Hi,
my project is based on the example 'ble_app_proximity' from SDK ver 17.0.2. When I set a longer DEVICE_NAME, for example
the string is cut up after the first 12...
Hello everyone,
I am developing a wearable device using the nrf52832 chip, sdk11.0.0 and s132_nrf52_2.0.0_softdevice.
Because of battery capacity limitation, I have to...
In UART async mode ( CONFIG_UART_ASYNC_API =y) the UART transmit data and receive callback works fine. I've been able to set up the callback and enable the rx.
After switching...
I'm currently setting up an environment in Visual Studio Code because the roadmap suggests going there.
I have experience with Segger and Nordic Segger and with Zephyr....
When I connected the usb and turn the DK switch on, the DK didn't turn on. After leaving for a few minutes, the DK started to turn on and off then eventually stables and fully...
Hi, I am coding an application on nrf connect sdk 1.9.1. which requires to send some data at 25packets per second. and each packet will be ~37 bytes. On the receiver side...
Summary: My custom board with an external crystal is consuming 208 µA when powered down under Zephyr, and I need to reduce it to less than 20 or so.
My board is based on...
Hi,
I'm working on a project trying to build a simple application on my own customize board with nrf52833 SoC.
After the configuration to my own board(Leds, button GPIO...
I'm attempting to store log data on my nRF52832 using the little file storage, and then allow a client to access this over BLE. From what I can tell, the data transfer can...
Hi,
I am using device nRF51822-CFAC, the SoftDevice is S130_nRF51_2.0.1(Id: 0x0087). In my project's General Options->Target->Device, I selected "NordicSemi nRF51822-CFAC...
Hi,
Could help me please?
What I need?
1) set GPIO pin as input with internal pulldown and set IRQ for Rising Edge.
In .overlay I add my pin like that:
Then in...
Happy Friday! So, I've fully funded on Indiegogo and now I'm in the application development stage. I'm new to development but I'm trying to build this app myself.
So far...
