hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
nRF52840, nRFSDK 17.0.2, SoftDevice S140 v7.2.0
Hello! We're turning on SoftDevice and using the PA/LNA pin control to drive our FEM. Then, we disable SoftDevice and issue...
Hi,
I found a bug in the init part of the LIS2DU12 driver. The driver tries to reboot the LIS2DU12 sensor using the SW_RESET bit in CTRL1 register even if it is not in...
Hi,
I'm trying to synchronize a process using an nRF52833 dev kit using a Zephyr event.
The code looks like this:
The first routine sends an event and the second captures...
I am working on an nRF52-based device using nRF Connect SDK (NCS) version 2.7.0. The device is configured to enter deep sleep every 60 seconds and wake up via a GPIO interrupt...
Hi,
I'm using the nRF Cloud multi-service application on my Thingy:91X.
I am using the Serial Terminal to see what networks are available, but when I go to attach manually...
Hello,
I've been working on a project using nRF52832 + NCS 2.1.1 including BLE and some sensors : MAX86150, MAX30205, MP34DT05, LIS3DH
I'm sending data of these sensors...
Hello! What are the steps I need to take to switch from BLE protocol to lets say the Gazelle protocol? Is it as simple as disabling the Softdevice? If such a function exists...
We are finishing up development of our product and looking into creating our Bluetooth listing. We are using the NRF52840 SoC (Fanstel BT840F model) with softdevice and NRF...
The NORDIC tutorials are great for demonstrating how to use GPIOs to drive LEDs and read buttons.
However, I need an 8-bit bus to exchange bytes with an external display...
Hi,
I am working on an application using the nRF52840 with the Quectel BG96 modem. I can successfully communicate with an insecure MQTT broker using the BG96 modem. Now...
Hi!
I'm making a new board using nrf54l15 and I found the following issue:
/* * PWM signal can be exposed on GPIO pin only within same domain. * There is only one domain...
We have a custom board with the NRF52840 running NCS v2.8.0.
We have a problem where our device will crash/lockup. From our testing so far, it seems to be related to Bluetooth...
I have a project for the NRF5340 with SDK 2.6.1. I test the code with twister using Unity and CMock. That works great. But now I have to adapt the unity_cfg.yaml (which is...
Hi,
DK:NRF54L15
Modify form the sample code:peripheral_uart
I add one spi21 and k_timer to get the sensor data, periodically. But got the error ZEPHYR FATAL ERROR 4...
Dear Nordic Support Team,
I am working on a project to measure distance using two E73-2G4M08S1C nRF52840 modules. I would like your guidance on the best approach for implementing...
