hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
Hi,
I am using ble_sdk_app_hids_keyboard example:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_hids_keyboard.html...
Hi
I used Toolchain Manager v0.10.3 to install nRF SDK v1.8.0 at Mac mini(Monterey - 12.1) two times get same issue.
The issue is Toolchain Manager just download toolchain...
I am using the nrf52840 on the Raytac MDBT50Q-1MV2 module. ( https://www.raytac.com/product/ins.php?index_id=24 )
I am supplying the module with 5v USB power to the VBUS...
Hi,
I'm currently trying to use littlefs as the storage backend for the settings subsys and the internal flash for the actual memory. LittleFS is working in general but...
Hi,
I am using two NRF5340 (one as peripheral and one as central) for our project. Both don't have any display and input capabilities.
For our use-case, I would like to...
Board: nRF52833
SoftDevice: s140
SDK version: 17.0.2
I've added OTA DFU feature to my application. I flashed pca10100_s140_ble bootloader and my application to my board...
We are using a custom nrf52832 HW configuration and the device is entering a state where it's drawing approximately 3mA without any obvious application layer functionality...
Hi,
I did respond to this:
https://devzone.nordicsemi.com/f/nordic-q-a/86426/peripheral-and-central-uart-sample-crash-when-sending-longer-messages
I do not see a update...
Hi, I have been learning my way around SES, nRF Connect SDK, nrf52-dk, and the sample projects for some time now.
When I wish to open another sample project, I follow the...
I program the uart example in my board nRF51 dk. I put a osciloscope in pin 9 and the signal is a square wave between 0 al 30V. So i think that the protocol is RS232, is this...
At a rate of 1M, the receiving sensitivity of the Bluetooth chip was tested, and during the test, it was found that the sensitivity may decrease whenever the frequency point...
Hi
We are working on an algorithm applicable to the indoor positioning of ships. We want to improve the algorithm further on top of the existing algorithm for Bluetooth...
I'm on a Comcast cable modem connection. When I've tried to pull up this site over the past few days, I've gotten "The page cannot be displayed because an internal server...
Dear nRF DevZone,
I have question regarding Zephyr k_sleep() function and NRF52840 timers.
I am developing an application for nRF52840 SOC and for that I am using nRF...
