I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I had my application running on nRF_SDK_For_Thread_and_Zigbee.
I have been following SDK APIs directly in my code to calculate certain parameters:
1. nrf_temp_read...
Hello,
I tried to power the nrf9160-DK with external supply on port P21, as suggered :
https://infocenter.nordicsemi.com/pdf/nRF9160_DK_HW_User_Guide_v1.0.pdf
So I...
As per DFU concept t he image management command handlers makes it possible to upload , list , test and confirm the image(s), while the OS management command handlers makes...
Hi,
We need to enable internal RTC of SDK,
Pls share location of RTC driver implementation in nrf Connect SDK 1.8 & 1.9
can you please share example code for enabling...
I have tried to used the function below.but it will make my key interrupt disable when i set gpiote_ch_id to 0 .My key is in PIN 0.11.
So I want to know the meaning of gpiote_ch_id...
Hi,
I would like to know if there is a footprint difference between NRF52810-QFAA-R and NRF52832-QFAA-R in other term, can I use both with the footpriint of NRF52810-QFAA...
Hi! I have mentioned this already 9 month ago in another ticket ( https://devzone.nordicsemi.com/f/nordic-q-a/75331/dfu-upgrade-of-only-bootloader-not-softdevice ) but it...
Hi ,
the nrf25840 data states regarding temperature sensor's accuracy: To achieve the measurement accuracy stated in the electrical specification, the crystal oscillator...
Hi, I use two nRF52840 DK for testing purposes for over 1.5 years now. Suddenly, yesterday the BLE module in one of the DK's stopped working. Just like that. Same functional...
Hellow
We are in trouble. Please tell me what to do.
The input range of the SAADC is not as expected.
I use: ・nrf52840 ・VDD=3.3V by Regulator ・nRF5_SDK_17.1.0 ・Sample...
The example ble_app_uart is working fine (i.e. I get NRF_LOG_INFO from gatt_evt_handler), but my code doesn't. I've checked the diff between them and tried adding all diffs...
Hi All,
I am using nRF52 DK board & nRF5_SDK_17.1.0 for Development(Emulated Project for nRF52805), My application needs creation of multiple service and multiple characteristics...
I bought a handful of nrf52840-Dongle boards, with the intention of developing an application on one "dev" board and then flashing it through the Open Bootloader on the others...
hi am working on DFU- OTA on nRF52833. In one of the query I found the method for to evaluate DFU- OTA on nRf52833 , am able to do that ,after connected to the Bluetooth I...
Hello,
I am new to Nordic. Earlier I was using Cypress controllers CYBT343026-01. As per nRF documentation, I believe once the controller goes into a deep sleep mode, I...
