Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
When I connect via USB the nRF9151 SMA DK to the computer, it doesn´t detect the board connected to it. The LED5 doesn't light up, ony the LED1 lights up with a weak flickering...
Dear all, I was excited with the announcement at WWDC last week that Apple was now supporting Bluetooth Channel Sounding on iOS 27 (currently Beta) They even had a session...
Hi,
I’m observing an issue in a Zigbee network where, after several hours of correct operation, the routers stop retransmitting the NWK broadcast frames sent by the coordinator...
Hi,
I'm working on a project where I need to sample an ADC with an accurate sample rate. It essentially works except that I do not get the correct rate from the timer...
We're using two nrf54:s, one DK (initiator) and one custom PCB with 2x antennas (reflector)
I've tried adjusting the samples so that multiple antenna paths are supported...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Dear Nordic Technical Support Team,
I would like to inquire about the following regarding the nRF54L series development:
Can I develop for the nRF54L series using...
I am using nRF54L10 with nRF Connect SDK v3.1. The device connects over BLE, wakes every 30 minutes to read sensor data, and then should enter deep sleep (System OFF). However...
Hello, I am currently experiencing an issue with the 802154_phy_test example on the nRF54L15-DK board, and I would appreciate your technical support.
[ Environment ]
...
Hi everyone,
We're using the "Manufacturer Specific Data" field within its advertising packets to send the firmware version to a phone application. It requires the company_indentifier...
Hello.
I am currently migrating a project from NCS v3.2.4 to v3.3.1 and transitioning from Partition Manager to devicetree-based partitioning, following the official migration...
Hi!
I am using nRF9151-DK, enabling UART1 and using CONFIG_UART_ASYNC_API.
The build is successful, but the problem every time i connect a flashed kit with this binaries...
Hi,
I have a couple of questions on migrating from Partition Manager to Devicetree since a particular example was not provided. Following the procedure in the SDK v3.3.0...
Hi everyone. I’m currently working on a custom board based on the nRF5340, but I’m unable to connect to the board when trying to flash it via the SWD interface using J-Link...
Hello
I want to clarify something because there seems to be a lot of conflicting information on Dev Zone, and the nRF5340 DK documentation doesn't specify the following...
