I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hello everyone,
In the Light Control Example of Zigbee SDK 4.1 there is a Light Switch with a couple of button assignments.
Used board: PCA10056
(Light switch) Button...
I am getting a
<debug> app: char val length 22 <debug> app: Failed to initialize characteristics. Error code: 0x04 <debug> app: Unable to create RegCertDataList characteristic...
Greetings,
In the nRF5 SDK for Thread and Zigbee v4.1.0 There's the "Zigbee CLI Agent Example".
Under this example the section "Using CLI to control lightning devices...
Hi, guys
I am debugging the I2S feature on nRF340DK, when I completed the initialization of I2S pins configuration and start I2S, the SCK,LRCK and MCLK pins can produced...
I'am new for this platform and working on nRF Connect SDK v1.6.1 with SES on windows.
i plan to develop based on a sample project. so, for example i select file-->open nRF...
I am trying to run and test the ots example but I am not able to connect to device with the nrfConnect or any other app? Please guide me as to how to check the ots service...
I am doing power optimizations on a custom hardware that has nrf9160 and nrf52833 on it. These are connected via GPIO pins and I use two pins to send interrupts to each other...
Hello. I am downloading a custom board (nrf52810) using the nrf52832-dk board as shown below.
I compressed and managed the project file after taking over for company business...
Dear Team,
We are developing a product based on ble mesh. We are planning to select NRF52840 as master device and nrf52832 as slave device. Slave devices should be more...
In the ble_app_beacon example in nRF SDK 17.02, there are two defines namely APP_BEACON_INFO_LENGTH (0x17) and APP_ADV_DATA_LENGTH (0x15). The former defines length of the...
I am trying to port some code from the nrf52840dk (PCA10056) to the dongle (PCA10059) and everything seems to work fine until an interrupt is triggered. All serial output...
Hey! I have a project with custom board with nRF52833 and I would need help with just getting data from sensor via i2c and sending it via bluetooth to mobile device. For some...
Hey!
I would like to use the nrfjprog executable from the nrf command line tools for flashing the nrf9160 modem firmware. I read some older tickets about this issue and...
I have a requirement to start the MCU with extended non connectable advertisement for few minutes and then activate normal connectable advertisement for another few minutes...
