Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Running nrf_drv_saadc_calibrate_offset() doesn't seem to work. I'm monitoring a 3v battery. Shown below is the debug output where the calibration is run after the event number...
Greetings,
We are attempting to install the nRF Sniffer program onto our nRF52833 DK as directed in the Nordic instructions. We've installed the nRF Connector S/W as well...
Hello All,
We are in the evaluation phase to implement openthread network in our gateway using nRF52840 as NCP device.
We require to have the number of end-device supported...
Hi,
I used to have a URL link for checking ibasis SIM card, such as devices, balances, etc. Now, I cannot find. My SIM card is from Nordic, so the login for ibasis account...
Hi Dev Team,
I am building an application wherein I need to send commands from the Cloud to a Thingy91 device. I tried out the cloud_client sample and I was able to send...
I have seen this problem posted several times in these forums but none of the existing solutions sit right with me.
I have an NRF52840 (using a UBlox BMD-340 dev board...
Hi Dev Team,
I have an application wherein I am publishing my sensor data every hour through MQTT using a Thingy91.
I am storing my sensor data value in a JSON format...
Hi,
I am trying to implement protobuf for my application. I have seen that nano-pb library is there in SDK file. I want to use it in BLE-UART communication. How to do with...
Hello,
I am using RFX2411N RF amplifier in my hardware design. I chose nRF52832 as an MCU. In nRF52832 datasheet, it is mentioned that the pins from P0.22 to P0.31 have...
Hi,
We are currently developing a Zigbee network based on nRF52840.
One of our devices was specially designed to contain 8 endpoints. But when an active ep request is...
Hi,
I'm using the BLE_app_interactive example as a starting point for my prototype (with SDK_17.0.2 and SoftDevice s132 ). I am using nRF52DK to read and write data from...
Hi
Im trying connect two peripheral devices through UART
The example project I used is "examples/peripheral/uart"
But i trace the code, it seems that the driver layer...
Hello,
I've been using nrfx UARTE driver on the nrf5 15.2.0 SDK on a nrf52832 and nrf52840 SoC and noticed that during the boot-up the first byte being sent is 0xFF.
Is...
Can I remove resistor R29 (ENCHG) on the ADP536 to disable the charging function and plug my 3.3V supply into the battery connector?
i.e. use the ADP536 for the power management...
