I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hello,
I am using SES V4.5, SDK 15.2 and the "ble_app_blinky_c" and I was not able to see the programme log.
I tried setting up the file "sdk_config.h" to use the RTT...
Hello,
I'm starting to develop an application using the DK pca10040 and SDK 15.3. At first I have just adapted peripheral ble_app_uart example and incorporated fds functionality...
Hi,
This may be a simple question, but I've gone through the infocenter and am still a little confused. I'm designing a PCB on which I'd like to have an nrf52840 that can...
Hi,
I recently purchased the nRF9160DK but cannot connect to o2's LTE-M network using the iBasis SIM, following the instructions given here: https://www.nordicsemi.com/Software...
When I trap an error in app_error.c in app_error_save_and_stop,
I mostly get a filename, line number, and an error code that I can understand.
However, sometimes I...
We are looking for a freelancer who can help to build a simple Proof of Concept of a load cell (strain gauges) ADC (HX711?) and the nRF52 development kit (810).
Objectives...
Central and peripheral is pairing and bonded. Central scanning with whitelist, if Slave is not online, master scan with whitelist will enter error when more than 30 seconds...
I'm using whitelist when bonded, but I want delete bonded then connect to anther device,.
But when scan again, whitelist_load is error. Try delete whitelist at the same...
Extended corruption occurs if DMA transfers for commands and data originate from the same RAM bank.
It is avoided if transfer of command bytes and transfer of data bytes...
Hello,
I ran into this list recently: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcomp_matrix_nrf52840%2FCOMP%2Fnrf52840%2FnRF52840_ic_rev_sdk_sd_comp_matrix.html...
Hi,
I'm using two nrf52840 Dev Kits and am trying to test out the ATT_MTU throughput example with SDKv16. Whenever I program one of my boards I get repeated fatal error...
I am pulling my hair, literally , I just can't get this company !
I am working with 4 IDE's in parallel and none of them has this stupidity .
I right click->add a new...
Background
I intend to use an nrf52 based board in remote inaccessible locations. It is important that I can always recover from a problem. As such, I want to use the watchdog...
Hi，
In the 07-5123-07-zigbee-cluster-library-specification specification, I see clusters that support CO2 and HCHO, but I did not see any definitions of CO2 and HCHO (cluster...
