I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hello, I'm experiencing an issue with communication between the nRF52840 and nRF9160 on the Thingy platform using the connectivity bridge. I successfully established communication...
Support,
Due to the limitations described in the referenced previous ticket, I am unable to successfully discover a service and its characteristics because of a hard fault...
I am struggling with the same requirement as this ticket :
ie receive from a UARTE without knowing in advance how many rx bytes to expect. This is typical for exchanging...
I'm running the nrf5340_audio application on the nRF5340 Audio DK and have a UART wired to TP60 and TP61. As long as I have USB (onboard j-link) or my Segger j-link connected...
We used to specify BOARD and BOARD_ROOT at the cmake level, but so far attempts to do the same using sysbuild did not succeeded. Is it still possible or should we rely on...
Hello,
Is it possible to know what is the cause of this assert : app: ZBOSS assertion in file: 24, line: 1024, please.
It is not very clear by reading the assembly code...
Hello,
Is it possible to know what is the cause of this assert : app: ZBOSS assertion in file: 24, line: 1050, please.
It is not very clear by reading the assembly code...
Recently the source control icon (git extension) in the activity bar in vs code shows more than changes in code.
As can be seen here the icon adds up the changes in...
AWS IoT example not working with v2.6.1 SDK with nRF7002 DK but works fine with v2.5.2 SDK.
*** Booting nRF Connect SDK v3.5.99-ncs1-1 *** [00:00:00.249,725] <inf> aws_iot_sample...
Hello all,
I use nRF52840 for my custom board. I set P1.11 & P1.12 as UART_RX & UART_TX. But these two pins can not work.
Here is my nrf52840dk_nrf52840.overlay.
Here...
In the Wi-Fi throughput sample code folder the main.c file has virtually nothing in it, just a few boilerplate lines and a main() with only two lines of code that set the...
Hi,
I have a nRF9160-DK (PCA10090, 1.0.0, 2020.50) that I am trying to flash with the Modem Shell using the Quick Start app on a M1 Max MacBook Pro, running macOS 14.5....
Hey guys, I'm trying to set the max tx power for our nRF52840 project and I'm getting this error:
CONFIG_BT_CTLR_TX_PWR_MINUS_1 was assigned the value y, but got the value...
I'm presenting an issue when exporting the data collected with the Power Profiler Kit 2 in the software (nRF Connect for Desktop v5.0.0), specifically the digital outputs...
Good afternoon,
I am debugging the nRF9160 in a product, and what we are noticing is that the socket "poll" events do not appear to be generated when the system is in...
