I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
If you look at the circuit of the PCA10040, it uses a 32Mhz 12pF crystal.
C1 and C2 of the crystal are 12 pF.
However, you say to use this formula: C1 = C_L * 2 - 4pF...
I am attempting to store a pre-generated key in the psa key store using the psa API. I have taken the nrf->samples->crypto->hmac and nrf->samples->crypto->persistent_key_usage...
Hi,
I am working on a setup where nRF5340 uses W5500 Ethernet IC and communicate MQTT over TLS. The actual setup for now is nrf5340dk + w5500 ethernet shield.
I am working...
We found one charging issue on nPM1100, after we assemble the battery to the PCBA, and then apply 5V to nPM110 (VBUS) and GND. The protection ciruit does not release, and...
Hi,
I am using nrf52840 and SDK-16.0. Our product is already in the market.
we added some extra features now. after adding this we are not getting application timer call...
Hi,
I need to provide a clock signal of 4.9152 MHz to an external ADC.
Can the NORA-B106 module (that integrate a nRF5340) supply that signal by the Application Core M33...
I am looking to program the nRF52840 development board to get data from the mpu6050 sensor. I want to use bare metal code for the same. Is there any available code or sources...
Hi Folks!
I've got a rather bulky project that's having a rather bulky project. In short, my project tries to enable both MCUBoot DFU and an ExFat Filesystem. I've narrowed...
Support,
I've encountered a challenge while integrating my product with device from a third-party. Unfortunately, they've utilized the SIG base UUID for their unregistered...
We have an existing application for the NRF52840 using SDKv15. This application will handle writing a new application to a free bank. I need to add the ability to jump from...
I need to do a DFU via BLE but I do not have enough memory. For the past few months I have been working on a custom bootloader that would use an external memory to do the...
Hello, I am on conenct SDK 2.6.0 and trying to run the Zephyr Bluetooth:Central example on the nrf5340 dk to connect to a Minew S4 door sensor and get data from it. Here is...
Hi, I am working on using nrf7002dk to connect to AWS over WiFi. So far I have been able to connect to WiFi and send a HTTP get request through DHCPV4. When I continue to...
In my nrf connect sdk projects i have external custom driver modules that i use across various projects to simplify code reuse. The issue i am having is that when I add MCUBOOT...
I am trying to use the the cellular monitor to get the device information but it seems like it does not connect to the device via J-Link, this is not a DK but a custom board...
