I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Good afternoon everyone, how are you?
I'm using custom hardware, Nrf52833+Nrf21540, already reviewed by and tuned by Nordic. We are going to carry out the tests for product...
I need to work on single bank DFU from esp32 to nrf52833. I found a website with instructions on single bank configuration here: academy.nordicsemi.com/.../topic /exercise...
Hello,
i'm working on a project where the system will be always in deep sleep unless there is an external event to wake him up. Upon this event, the system connects through...
Hello, I have a question about how to operate on multiple Zigbee devices simultaneously. I am currently developing a hub to control and retrieve data from home appliances...
I want to make a secure pairing with Bluetooth. Let it first pair with the device, then connect directly without pairing. Maximum how many devices can I register?
Hi,
I'm using an nRF52832 in SDK v.17.1.0 and, starting from the ble_app_uart example code, I'm sending data from the board to another device. I want monitoring it with...
Hey all,
I'm looking for a bit of guidance here to nail a bus fault that happens about 30 minutes into the program.
The message is the following:
Reading through previous...
Hello
I am trying to test the esl example project.
Is there a simple, accurate, step by step guide for this?
Current documentation has some incorrect sections and when...
Hi Team
Customer want to use Bluetooth_Base_UUID (00000000-0000-1000-8000-00805F9B34FB) as 128 bit UUID base. They can use any other 128 bit UUID base but this one. When...
Hello, I'm working on an application with precise timing requirements. Basically I need to generate a short pulse and sample two channels during the pulse. In addition, I...
I use the nrf5340.
I want to filter 8 devices with different addresses.
When scan_filter_match() recognizes one of the addresses, can you quickly identify which of the...
Hello, I built a matter-over-thread firmware for nrf52840 on the Matter SDK 1.3-sve branch and NCS 2.5.0 version. It work well with Apple, Google and chip-tool, but commissioning...
Dear sir or madam,
I am facing a peculiar issue. In my application, I am using nrf52840 dongle and I am setting several GPIO pins as output pins with output value high...
Hello DevZone,
I am developing battery powered Zigbee end device. Using nrf Connect SDK 2.6.0 on nrf52840 chip.
I have issue that I am trying to solve. From time to time...
Hello there,
I was using 2.5 SDK on my development. Recenelty I updated the SDK to the latest of 2.7.0-rc3. I got many warnings.
Then, I created a brand new BLE NUS project...
