I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
I use the nrf_dm demo program, when using the nRF52840DK development board, the program can print the log normally.
Then I changed the build configuration to nRF52840Dongle...
Hello,
I have a custom nrf5340 board with a simple firmware flashed on it (turn on red led). My board has a hall sensor as a turn on/off switch (latched). If I connect it...
I used nRF52840 board with SDK 17_1_0 ,
Using FDS I am able to read and write data into flash when nRF52840 board Continuous ON,
But when i Make nRF52840 board Power OFF...
How can I blacklist BT LE channels/frequency from operation? Context: I have the nRF52840 integrated into our product's design. The device is going into an environment where...
I just upgraded my nRF Connect for VSC to 2.6.1 and now am getting these errors:
and
I saw this as well:
but I have CONFIG_DISPLAY =y in the prj.conf....
I have an application running on a custom nRF5340 board that supports simultaneous BLE DFU of the network and application core with MCUBoot. This ticket: seems to indicate...
How can I properly set up the SWD interface for printk on a custom PCB? I have to build my project example and see the message printed on the VS Code console. My custom hardware...
Using nrf5340 as both Central and Peripheral roles and I have implemented the Basic Audio Profile based on the nrf5340 audio example. I am using nRF Connect v2.6.1.
I...
I need a bluetooth module that is capable of simultaneously streaming audio two way, ie two channels stereo out and 1 channel mic in with low latency. A friend had recommended...
Hi folks!
As always, I'll start with relevant environment details
===== Environment =====
nRF Connect SDK v2.5.0 (though not opposed to upgrading to one of the 2.6.X...
Hi,
We are developing a device using nRF5340+nRF7002 running Matter. The problem we have is the code size which is around 900KB when Matter is enabled. This leaves us with...
Hi,
My custom board nRF52840 works as a Peripheral, which advertises itself for connection from a Central.
The project is built based on peripheral_hr sample project....
Dear:
I can upgrade applicaiton ONLY sucessfully through DFU.
but now, i want to upgrade applicaiton+softdeivce+bootloader to deployed devices. do you have such documets...
Hi,
What is the maximum PWM frequency one can achieve on the nrf52840 with 50% duty cycle? Sample .dts and c-code in NRF Connect SDK would be appreciated!
In practice...
