Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi,
We are developing on a nRF52832 MCU and we tried to enable MPU on the whole RAM region (addr: 0x20000000, size : 0x10000) But when we create a new MPU region around...
Hi,
So I have seen there is a clean -up option to set the architecture core HW registers to their warm -reset values as specified by the architecture before running the...
Hello everyone,
using Segger Embedded Studio, I encountered an issue with the TWI libraries. My device consists of a custom PCB controlled by the nRF52840 (programmed with...
A simple and maybe trivial question. When in a thread I wait data for example with
is it like call continuously the k_yield()? How the api above works in the underhood...
Hi
is there any example or Tutorial to start from the beginning stage of developing Multiprotocol (BLE and Thread)?
I've tried searching many articles still unable to...
Hi,
Chip: nRF52840
OS: nRF Connect / Zephyr: v2.3.0
Problem: Saving coredumps to external flash
We're trying to add a bunch of debugging features to our firmware before...
I am using the PCA10040 nRF52DK board
I want to connect the UART RX and TX pins of the nRF52832 to my target CPU
I have cut the connections at SB16 and SB14
I can see...
Hi Sir,
As we know, Matter 1.3 supports Electric Vehicle Charging.
Do we have any plan to support the example of Electric Vehicle Charging?
If yes, what is the time...
Hi, We are using a Segger JLINK to program a nrf5340 product using the SWD interface. We have been successfully programming units using a design where there is a 100k pullup...
When we try to test the stability of the UARTE peripheral, we find that when inserting and removing the RX pin, the uarte_handler callback function is very likely to goes...
What is the recommended UART SUSPEND sequence to use the PM_DEVICE_RUNTIME? I am having trouble using the PM capabilities with the UARTe driver. I am developing on the 52833...
Hi,
I am trying the https://github.com/NordicDeveloperAcademy/bt-fund blefund_less1_exer1 using nRF52840 DK. I am able to connect but not able to detect button press. I...
SDK:17.1
application: ble_app_uart(+ble_app_buttonless dfu service) bootloader:secure bootloader pca10040e_s112_ble I want to know what operations will be performed when...
Hello,
I saw in an old forum thread ( https://devzone.nordicsemi.com/f/nordic-q-a/79412/lwm2m-amount-of-object-instances-limited ) that block transfer was not fully supported...
