I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
I'm testing the SPI-slave functionality based on the routine ncs/v3.3.0/zephyr/tests/drivers/spi/spi_controller_peripheral .
The original code uses the pins of SPIS21 ,...
Hi DevZone,
I am currently working on an external Flash OTA update via SQSPI on the nRF54L15 DK (v0.7.0). I have already verified that SQSPI read/write operations are...
Hi, I'm using a WisBlock setup with: • RAK19001 base board • RAK4631 core RAK18030 microphone in IO slot A • RAK15002 microSD in IO slot B I'm running Zephyr / nRF Connect...
nRF54L15 DK Board
BM-SDK-V1.0
Hi：
I have debugged the IRQ according to the nrfx demo, but now there is an unresolvable error that requires assistance.
This is an error...
Hello Nordic-Team,
I am using the SENSING mechanism on GPIOs to wake up a firmware from SYSTEM OFF. Two GPIOs are used for this and it is crucial for the firmware to detect...
I'm using nRF Connect for Desktop on Linux and updated today to v5.3.0.
I have J-Link V9.24a installed and it is available in $PATH. Also it works well with Programmer v4...
Hello Nordic Team,
We are currently working with the nRF54LM20B device and would like to understand whether Bluetooth Channel Sounding is supported on this SoC.
Specifically...
Hi,
This is more of a bug-report than really a help question, as it can be dealt with.
The device I am developing uses an external flash for storing MCUBoot's slot-2,...
I have been working on a soil moisture sensor for my indoor plants and I wanted to build some skills in PCB design using a Nordic SoC. I have chosen the nrf54L15 for this...
Hello Nordic Team,
I am working on a project based on the following requirements, where I have added multiple configurations and peripherals in my firmware, and I need to...
Dear Nordic Team,
We are seeking assistance in resolving a significant power consumption gap observed in our nRF9151-based asset tracker. While our lab testing suggests...
Hi all,
I'm working on BLE time synchronization between nodes using hardware timestamps via GRTC + DPPI + PPIB cross-domain. CRCOK and PHYEND work perfectly, but adding...
Hello Nordic Team,
I am working on an application using the nRF52833 with the following requirements:
Device operates as both BLE Central + Peripheral
Stores bonding...
Hi,
I’m looking to program an external device that runs on 3.3V with my NRF52840 DK (v3.0.1), and I’m looking to verify that this is possible. I know that the DK runs at...
It seems there might be a small issue with the TF-M GPIO MCU-select IOCTL plumbing on nRF54L — specifically when a non-secure app tries to configure sQSPI GPIOs (and presumably...
