I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
My name is Thomas Ramberg and I'm the founder of Dory in Norway ( dorysign.com ) an upcoming product that is using the Nordic nRF52840 chip. We are about to do CE and FCC...
Hi,
I have a central application that runs on nRF52833 soc. I want to connect it with my nrf connect for mobile app, so I've created a new advertising packet in the advertiser...
Good day, sirs
I am trying to imply function that one central device could connect to max 3 devices, only one device active, while switch active device between the three...
Hi,
I'm working on SDK 15,
When initializing USBD using function app_usbd_init, I found that if APP_USBD_CONFIG_POWER_EVENTS_PROCESS = 0,
it disabled all USBD event...
HI everyone, i have a problem when implementing Butterworth bandpass filter in SAADC module to cancel out the noise of our ECG module.
I used " nrf_saadc_value_t m_buffer_pool...
---
I want to apply whitelist and peer manager to an existing project Now, the whitelist is not applied, and if you give the 'scan start' command, the scanned device lists...
Hi Team,
We are developing an application where we have PWM like pulses coming from our sensor. Max frequency of this would be around ~8k. We want to poll the number of...
Hi Team,
I am initialized to work on NRF52840 Dongle
Here I want to see the log or print statement for my developing purpose
i used tera term to view my log but no statements...
Hi,
I have 3 nRF5340 Audio DK's and want to decrease the sample rate and the bit rate. By now, I have changed the rates in the .config and autoconf.h files (from 48kHz to...
hello, team:
I'm new to the nrf5340 develop.I have installed the nrf connect SDK v2.0.2 many times.
when the installation end,I can only find nothing but the '.git' in...
Hi
The documentation of nRF5340 Audio Application of nRF Connect SDK 2.1.1 mentions "onboard hardware codec" and "external hardware codec".
From https://developer.nordicsemi...
I am using a development system that uses a Microchip MCP2515 chip which has the drivers included with Zephyr and everything works perfectly with 52840dk board. Who can tell...
Hi,
I am evaluating the nRF5340 Audio DK by applying the sample code nRF5340_audio.
I tried changing the frame to 7.5 ms by editing prj.conf as below and no audio came...
Hello everyone
i am used Arduino nano ble 33 board in that board nrf52840 is used anyone known how to increase Tx power of Bluetooth i am used Arduino ide for coding
