I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v2.0.0 I could build with NCS v1.9.1 but I cannot build with NCS2.0
[Build log] In file included from C:/NCS200/v2.0.0/zephyr/include...
I have an Ellisys Bluetooth Explorer 400 sniffer and am trying to sniff the ISO audio data between nrf5340 ADK boards. I enabled CONFIG_BT_LOG_SNIFFER_INFO, CONFIG_BT_DEBUG_KEYS...
Hi there. I am trying to utilize both the network core and the application core to perform two separate tasks at the same time. I have looked through some of the sample projects...
Hi, I need to setup a vendor specific class USB device driver. The driver shall present the following data endpoint:
0x84 for Bulk IN endpoint 0x03 for Bulk OUT endpoint...
SEGGER Embedded Studio for ARM can't connect to nRF52832 device. But J-Link RTT Viewer can connect to nRF52832 device. The following is log messages of J-Link RTT Viewer....
Hi there,
I am currently developing on the nRF5340DK and am doing some very processor-intensive work (@ 128MHz) on data read from the QSPI bus. I would like to set up non...
Hi, I have been trying to build an example of console usb example and then build it for thingy91_nrf9160_ns but got an error :
I have been trying this code several weeks...
Hi, with appropriate pm_static.yml and dts.overlay we managed to setup a LittleFS instance over external flash. However this broke the Settings storage subsystem the BLE stuff...
hi support team,
for our sdk17.0.2 demo hid_keyboard, i tested it and using IOS mobile to pair with our 840dk or 832dk
find out after lots of reset the keyboard device...
I am developing an application that uses nRF52840 wake on NFC, and spends most of its time in system OFF state with NFC wake enabled.
Per the nRF52840 Product Specification...
On the NRF52840 dongle am building a protocol on USB CDC ACM.
Using app_usbd_cdc_acm_read to read one byte at a time works perfectly.
However, I can seem to make app_usbd_cdc_acm_read_any...
Hi,
I am developing a wireless product in which i want to use nRF52 in ESB mode.
The product is battery powered and should be sleep mode.
What i have decided to do is...
Hi,
I have read the thread here: which implies that this config option might not work?
Does it work? I would like to build mcuboot and then always use the same binary...
