Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi,
I was evaluating 9160DK. I tried the GPS example using 1.7.1 SDK and it works great outdoor. However, I tried to use a hackRF one to emulate the GPS signal. 9160 shows...
Hi
I still have a number of devices that are based on nRF24E1. From time to time the chips need a change in firmware. Since the last time I updated them, my PC has crashed...
Hi support team
I have been modifying the throughput example (nRF5 SDK v17) to connect the receiving unit (AMT client) to more than one device. I am running this on the...
Good day
I have Ubuntu 20.04.3 LTS installed on my laptop + fresh installation ( ~/.nrfconnect-apps was cleared and app reinstalled ) of nRF Connect 3.9.1
I use Bluetooth...
Hello!
My steps:
1 - Full working dfu over ble on nrf52840-dk + nrfutil + nrf52840 Dongle
2 - Change transport BLE -> ANT + nrfutil + ANT USB Stick 2, ANT USB(two different...
I am new in nrf52832 field i am trying to send some customized data(scan response) in ibeacon format of advertising. suggest me some ways or code to do the same
Thankyou...
Hi,
I have a custom EVB from Taiyo (EYSPBNZUA), https://www.yuden.co.jp/jp/product/category/module/img/TY_BLE_EYSPBNZUA_DataReport_V1_0_20201019E.pdf
When I press the...
Using above strategy for frequency measurement. Frequency source connected with one gpio pin.
Only GPIOTE PPI Timer modules are involved
HFXO is in use full time through...
I recently installed nrf connect sdk manually on windows 10.I found that i am able to open sample projects in segger embedded studio but not able to open our developed project...
Hi, everyone
I'm developing nRF52832 S132 with SDK 17.0.x
I wanted to change MTU size to 247 using 2 peripheral link in ble_app_multiperipheral example.
but i...
Hi Sir/Miss,
I try to implement static passkey in my project. Which is using nRF52810.
The SDK version is 17.0.2.
Softdevice is S112.
My project is based to develop...
hardware: NRF52832
SDK:17.02
I'm trying to get SPIM working with a RF(SX126). I'm currently trying to use the nrf_drv_spi_transfer() function.
I need to read and write...
Hello everyone,
I have a problem with my device name. First of all I want tro write the device ID into the device name. I get the device ID over "RF_FICR->DEVICEID[0]"....
Dear Members,
How can I stop ANT HRM channel temporarily, and save the heart rate value on to SDcard ?
My code at static void page0_data_log(ant_hrm_page0_data_t const...
Hello,
I’m designing a custom nrf52832 device and i came across an issue with energy buffering. I am using inside of the device the battery CR2032, SoC nrf52832 and two...
